Pelco C3463M-B manual Installation, Switch Settings

Page 7

Installation

This manual contains installation instructions for the Spectra IV dome drive only. For complete installation instructions for a Spectra IV dome system, refer to the installation manual that was shipped with the back box.

SWITCH SETTINGS

Before installing the dome drive, you must configure the receiver address, termination, and baud setting. The DIP switches used to configure these settings are located on the base of the dome drive.

Figure 1 shows the default settings for the DIP switches. Switch SW1-1 (SW1, switch 1) is set to the ON position; all other switches are set to the OFF position.

Refer to the following sections to set the address, termination, and baud settings for the dome drive.

O N

 

 

 

 

 

 

 

 

SW2

 

 

 

 

 

 

 

 

 

1

2

3

4

5

6

7

8

9

10

SW1

O N

 

 

 

 

 

 

1

2

3

4

5

6

7

8

Figure 1. Default Switch Settings

SW1: RECEIVER ADDRESS

Set the SW1 switches for the address of the dome drive. The following information is required to set the dome drive address:

Pelco P-type control: The default address is 2. Refer to Table F on page 64 for address settings that use Pelco P-type control. The maximum number of receivers is 32.

Pelco D-type control: The default address is 1. Refer to Table G on page 65 for address settings that use Pelco D-type control. The maximum number of receivers is 254.

SW2 SWITCH 1: AD-32 PRESET SYSTEM

SW2-1 should be set to the ON position if an AD-32 controller and Pelco’s TXB-AD translator board are used to control the dome system.

SW2 SWITCH 2: CM9502 SETTING

If a CM9502 matrix system is used with the dome drive, set SW2-2 to the ON position.

SW2 SWITCH 3: CONTROL SYSTEM COMPATIBILITY

Coaxial Control Systems

Although Spectra IV dome systems can operate with coaxial control systems from many manufacturers, the system is designed for optimal performance with Pelco Coaxitron® control products within the length specified for coaxial cable.

To compensate for coaxial control systems from other manufacturers, Pelco has provided DIP switch SW2-3. Setting SW2-3 to the ON position may improve dome control with these control systems.

If you are using a Pelco Coaxitron controller, leave SW2-3 in the default OFF position.

NOTES:

•This coaxial control system compatibility feature is only available for dome drive revisions A4 and later (revisions A0 and later for Spectra IV Horizon dome drives). The revision number can be found on the barcode label on the top of the dome drive. Software version 1.090 and later indicates this mode is available by placing an asterisk next to the switch number in the Dip Switch Information menu.

•In some configurations, Pelco CM9502 Series matrix systems use nonstandard Coaxitron commands for functions like pattern playback. If you experience problems with these functions, set SW2-3 to the ON position.

C3463M-B (2/11)

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Spectra IV SL and Spectra IV SE Series Page Contents Field Align Page Description Switch Settings InstallationSW2 Switches 6 to 8 Baud Settings SW2 Switches 4 and 5 Serial Port SettingsAddress Dome DriveOperation Quick Configuration GuideQuick Operation Guide Extended Coaxitron or RS-485 Mode Preset 95 Accessing Main MenuDigital Sentry System Software Endura WorkstationDigital Sentry DS Controlpoint 23X LowLight Day/Night Menu Tree Password Edit the Password Dome SettingsLine Sync Presets AlarmsPatterns Zones Alert Current Reading Clear Password27X LowLight Day/Night Menu Tree Label PositionEvent Edit Event Power UP Line Sync Presets Motion Detection35X LowLight Day/Night Menu Tree Azimuth Elevation Zoom Custom Camera Settings Language Reset Camera Cycle Camera Power Reboot System ExitSpectra Language System Information DIP Switch InformationExit Display Setup Preset Label Display SetupRestore Factory Defaults Back Exit Alert Message Title Text Save and Exit Cancel HelpLabel Positions EventAuto Focus Dome SettingsCamera Type of LightingPT Focus Lock Zoom LimitZoom Speed LOW Light LimitAuto IR Level IR CUT FilterLow Light Focus Auto Iris Advanced Camera SettingsShutter Speed AGC LimitElectronic Image Stabilization Auto SharpnessAuto White Balance Backlight CompensationField Align OFF Low lux noise reduction is disabledLOW LUX Noise Reduction Video LevelAuto Flip Motion SettingsLOW Light Sharpness Minimum Focus DistanceLimit Stops Preset Freeze FramePark Time Scan SpeedAuto Tracking Power UP Start Time Line Sync Zoom Presets Lost ActionAuto Tracking Azimuth ZeroZoom Display SetupSensitivity Start TimePower UP Action Power UPBack Exit Power UP Power UP Action Back Exit Presets Preset Number PresetsTable C. Stored Presets by Back Box Model Back Exit Line Sync Line Sync PhasePreset 96 Stop a scan Preset 83 to 87 ReservedPreset 92 to 93 Scan limit stops Preset 94 Reserved Preset 95 Select main configuration menuAbcdefghij Cancel Klmnopqrst Uvwxyz Label for Preset Preset NumberSpace Motion Detection Enable Motion DetectionEdit Detection Areas Edit Schedule Activate Aux CommandAux Time Back Exit Patterns PatternsBack Exit Clear Zone Back Exit ZonesBack Exit Zones Zone Number Edit Zone LabelWindow Blanking Enable Window Reverse Clear Window Back ExitTo set a window blanking area Reverse DisabledClear Window Blank All Above Blank All Below Blank ALL ABOVE/BLANK ALL belowBlanked Area Alarms C3463M-B 2/11 AUX Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeDwell Time Secs Edit Schedule Back Exit Back Exit Title Text Title TextEdit Title Text System Condition Alert Message AlertRepeat ACK ActionCurrent Reading Reset AlertNone default Not activated Activate AUXBack Abcdefghij Cancel Klmnopqrst Exit Uvwxyz PasswordBack Exit Password Enable Password Edit PasswordClock Follow the instructions in for Fixed DATE, adding Week Holiday EventEvent Type Back Exit Event Event Type Event LabelEdit Event Label Event LabelEdit Event Edit Holiday Clear EventList Event HolidayMonth January DAY Back Exit Clear HolidayList Holidays Edit Holiday OccurrenceScheduled Events Example Preset Weekend 1100 AM Sat-SunUse this page to record scheduled events Reboot System Reset, Cycle Power, RebootReset Camera Cycle Camera PowerSoftware/Language File Upload Maintenance Zoom Speed 4.2/5.8 seconds Horizontal Angle of View SpecificationsSignal Format 23X ModelsDD427 27X ModelsDD4CBW35 35X ModelsAppendix Table F. Switch Settings for SW1 Pelco P-Type ControlSpectra Switch Setting Address Table G. Switch Settings for SW1 Pelco D-Type Control 1Table G. Switch Settings for SW1 Pelco D-Type Control 2 Table G. Switch Settings for SW1 Pelco D-Type Control 3 Table G. Switch Settings for SW1 Pelco D-Type Control 4 Table G. Switch Settings for SW1 Pelco D-Type Control 5 Table G. Switch Settings for SW1 Pelco D-Type Control 6 Product Warranty and Return Information
Top Page Image Contents