Pelco C3463M-B manual Preset 95 Accessing Main Menu, Extended Coaxitron or RS-485 Mode

Page 11

PRESET 95: ACCESSING MAIN MENU

You can call up the main menu on your monitor by configuring (setting or creating) preset 95 (preset 28 in AD-32 preset mode).

Configuring preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for configuring preset 95 are given below for various Pelco controllers.

CM6700/CM6800

1.Enter the number of the Spectra IV dome system and press the CAM key.

2.Enter 95 and hold the PRESET key for two seconds.

3.In the Edit Preset menu, go to SET and press the ACK key. The main menu appears.

KBD200A/KBD300A: Direct Mode Only

1.Enter 95.

2.Hold the PRESET key (approximately five seconds) until the main menu appears on the screen.

CM9500

1.Enter the number of the Spectra IV dome system and press the CAM key. The main menu appears.

2.Highlight SETUP in the main menu and press the SELECT key.

3.Highlight CAM in the Setup menu and press the SELECT key.

4.Highlight PRESET in the Camera menu and press the SELECT key.

5.Enter 95 and press the F1 key. The main menu appears.

CM9740/CM9760/CM9770/CM9780

1.Press the ESCAPE key to open the main menu. Select DEF. The Define submenu appears.

2.Enter your four-digit PIN if this is your first time entering this mode.

3.Enter 95 and select PRST. The main menu appears.

4.Select the Quit icon to return to the default menu.

KBD4000/KBD4002

1.Press the SPOT MONITOR key.

2.Enter 95, then hold the PRESET key (approximately five seconds) until the main menu appears on the screen.

MPT9500

Extended Coaxitron or RS-485 Mode

1.Enter 95 and press the PRESET SET key.

2.Press the F2 key. The main menu appears.

NET300/NET350/NET4001A

1.Check the Set box.

2.Click the preset 95 button. The main menu appears.

C3463M-B (2/11)

11

Image 11

Contents Spectra IV SL and Spectra IV SE Series Page Contents Field Align Page Description Switch Settings InstallationSW2 Switches 6 to 8 Baud Settings SW2 Switches 4 and 5 Serial Port SettingsAddress Dome DriveQuick Operation Guide Quick Configuration GuideOperation Extended Coaxitron or RS-485 Mode Preset 95 Accessing Main MenuDigital Sentry DS Controlpoint Endura WorkstationDigital Sentry System Software 23X LowLight Day/Night Menu Tree Password Edit the Password Dome SettingsLine Sync Presets AlarmsPatterns Zones Alert Current Reading Clear Password27X LowLight Day/Night Menu Tree Label PositionEvent Edit Event Power UP Line Sync Presets Motion Detection35X LowLight Day/Night Menu Tree Azimuth Elevation Zoom Custom Camera Settings Spectra Language Reset Camera Cycle Camera Power Reboot System ExitLanguage System Information DIP Switch InformationRestore Factory Defaults Back Exit Display SetupExit Display Setup Preset Label Alert Message Title Text Save and Exit Cancel HelpLabel Positions EventAuto Focus Dome SettingsCamera Type of LightingPT Focus Lock Zoom LimitZoom Speed LOW Light LimitLow Light Focus IR CUT FilterAuto IR Level Auto Iris Advanced Camera SettingsShutter Speed AGC LimitElectronic Image Stabilization Auto SharpnessAuto White Balance Backlight CompensationField Align OFF Low lux noise reduction is disabledLOW LUX Noise Reduction Video LevelAuto Flip Motion SettingsLOW Light Sharpness Minimum Focus DistanceLimit Stops Preset Freeze FramePark Time Scan SpeedAuto Tracking Power UP Start Time Line Sync Zoom Presets Lost ActionAuto Tracking Azimuth ZeroZoom Display SetupSensitivity Start TimeBack Exit Power UP Power UP Action Power UPPower UP Action Back Exit Presets Preset Number PresetsTable C. Stored Presets by Back Box Model Back Exit Line Sync Line Sync PhasePreset 96 Stop a scan Preset 83 to 87 ReservedPreset 92 to 93 Scan limit stops Preset 94 Reserved Preset 95 Select main configuration menuSpace Label for Preset Preset NumberAbcdefghij Cancel Klmnopqrst Uvwxyz Edit Detection Areas Enable Motion DetectionMotion Detection Aux Time Activate Aux CommandEdit Schedule Back Exit PatternsBack Exit Patterns Clear Zone Back Exit ZonesBack Exit Zones Zone Number Edit Zone LabelTo set a window blanking area Enable Window Reverse Clear Window Back ExitWindow Blanking Clear Window DisabledReverse Blanked Area Blank ALL ABOVE/BLANK ALL belowBlank All Above Blank All Below Alarms C3463M-B 2/11 Dwell Time Secs Edit Schedule Back Exit Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeAUX Edit Title Text Title TextBack Exit Title Text System Condition Alert Message AlertRepeat ACK ActionCurrent Reading Reset AlertNone default Not activated Activate AUXBack Abcdefghij Cancel Klmnopqrst Exit Uvwxyz PasswordBack Exit Password Enable Password Edit PasswordClock Follow the instructions in for Fixed DATE, adding Week Holiday EventEvent Type Back Exit Event Event Type Event LabelEdit Event Event LabelEdit Event Label Edit Holiday Clear EventList Event HolidayMonth January DAY Back Exit Clear HolidayList Holidays Edit Holiday OccurrenceUse this page to record scheduled events Example Preset Weekend 1100 AM Sat-SunScheduled Events Reboot System Reset, Cycle Power, RebootReset Camera Cycle Camera PowerSoftware/Language File Upload Maintenance Zoom Speed 4.2/5.8 seconds Horizontal Angle of View SpecificationsSignal Format 23X ModelsDD427 27X ModelsDD4CBW35 35X ModelsAppendix Table F. Switch Settings for SW1 Pelco P-Type ControlSpectra Switch Setting Address Table G. Switch Settings for SW1 Pelco D-Type Control 1Table G. Switch Settings for SW1 Pelco D-Type Control 2 Table G. Switch Settings for SW1 Pelco D-Type Control 3 Table G. Switch Settings for SW1 Pelco D-Type Control 4 Table G. Switch Settings for SW1 Pelco D-Type Control 5 Table G. Switch Settings for SW1 Pelco D-Type Control 6 Product Warranty and Return Information