Pelco C3463M-B manual Auto Tracking, Azimuth Zero

Page 31

To set manual or scan stops:

1.Use the joystick to position the cursor beside SET MANUAL STOPS or SET SCAN STOPS.

2.Press Iris Open.

3.Follow the directions displayed on the monitor.

NOTE: In order for the manual or scan stops to work, the LIMIT STOPS option must be ON.

To clear manual or scan stops:

1.Use the joystick to position the cursor beside CLEAR MANUAL STOPS or CLEAR SCAN STOPS.

2.Press Iris Open.

3.Follow the directions displayed on the monitor.

AZIMUTH ZERO

Azimuth is the pan angle from zero to 359 degrees. Azimuth zero is the pan position you specify to be the zero degree point. Azimuth zero is normally set to magnetic north. Once set, azimuth and compass readings are based on the set Azimuth Zero point.

To configure azimuth zero:

1.Use the joystick to position the cursor beside SET AZIMUTH ZERO.

2.Press Iris Open.

3.Follow the directions displayed on the monitor.

To clear azimuth zero:

1.Use the joystick to position the cursor beside CLEAR AZIMUTH ZERO.

2.Press Iris Open.

3.Follow the directions displayed on the monitor.

AUTO TRACKING

(Applies to 27X and 35X models only.)

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS> ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT


DOME SETTINGS				AUTO TRACKING
<CAMERA>				AUTO TRACKING	OFF
<MOTION>				DISPLAY SETUP	ON
<AUTO TRACKING>				SENSITIVITY	HIGH
<POWER UP>				START TIME	60
<LINE SYNC>				ZOOM	ON
<LINE SYNC>				ZOOM	ON
<PRESETS>				LOST ACTION	STOP
<PATTERNS>				RETURN	OFF
<ZONES>
<WINDOW BLANKING>
<ALARMS>
<AUX>
<TITLE TEXT>
<ALERT>*
<CLEAR>
<PASSWORD>
<CLOCK>
<EVENT>
BACK
EXIT

AUTO TRACKING

Auto tracking allows the camera to automatically pan, tilt, and zoom to track objects of interest (people, cars, and so forth) when motion is detected in a scene without requiring an operator to manually control the camera’s PTZ movements. There are two settings:

ON: Auto tracking is enabled.

OFF (default): Auto tracking is disabled.

NOTE: If the auto tracking setting is OFF, all other settings in the Auto Tracking menu are disabled.

C3463M-B (2/11)

31

Image 31

Contents Spectra IV SL and Spectra IV SE Series Page Contents Field Align Page Description Switch Settings InstallationSW2 Switches 6 to 8 Baud Settings SW2 Switches 4 and 5 Serial Port SettingsAddress Dome DriveOperation Quick Configuration GuideQuick Operation Guide Extended Coaxitron or RS-485 Mode Preset 95 Accessing Main MenuDigital Sentry System Software Endura WorkstationDigital Sentry DS Controlpoint 23X LowLight Day/Night Menu Tree Password Edit the Password Dome SettingsLine Sync Presets AlarmsPatterns Zones Alert Current Reading Clear Password27X LowLight Day/Night Menu Tree Label PositionEvent Edit Event Power UP Line Sync Presets Motion Detection35X LowLight Day/Night Menu Tree Azimuth Elevation Zoom Custom Camera Settings Language Reset Camera Cycle Camera Power Reboot System ExitSpectra Language System Information DIP Switch InformationExit Display Setup Preset Label Display SetupRestore Factory Defaults Back Exit Alert Message Title Text Save and Exit Cancel HelpLabel Positions EventAuto Focus Dome SettingsCamera Type of LightingPT Focus Lock Zoom LimitZoom Speed LOW Light LimitAuto IR Level IR CUT FilterLow Light Focus Auto Iris Advanced Camera SettingsShutter Speed AGC LimitElectronic Image Stabilization Auto SharpnessAuto White Balance Backlight CompensationField Align OFF Low lux noise reduction is disabledLOW LUX Noise Reduction Video LevelAuto Flip Motion SettingsLOW Light Sharpness Minimum Focus DistanceLimit Stops Preset Freeze FramePark Time Scan SpeedAuto Tracking Power UP Start Time Line Sync Zoom Presets Lost ActionAuto Tracking Azimuth ZeroZoom Display SetupSensitivity Start TimePower UP Action Power UPBack Exit Power UP Power UP Action Back Exit Presets Preset Number PresetsTable C. Stored Presets by Back Box Model Back Exit Line Sync Line Sync PhasePreset 96 Stop a scan Preset 83 to 87 ReservedPreset 92 to 93 Scan limit stops Preset 94 Reserved Preset 95 Select main configuration menuAbcdefghij Cancel Klmnopqrst Uvwxyz Label for Preset Preset NumberSpace Motion Detection Enable Motion DetectionEdit Detection Areas Edit Schedule Activate Aux CommandAux Time Back Exit Patterns PatternsBack Exit Clear Zone Back Exit ZonesBack Exit Zones Zone Number Edit Zone LabelWindow Blanking Enable Window Reverse Clear Window Back ExitTo set a window blanking area Reverse DisabledClear Window Blank All Above Blank All Below Blank ALL ABOVE/BLANK ALL belowBlanked Area Alarms C3463M-B 2/11 AUX Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeDwell Time Secs Edit Schedule Back Exit Back Exit Title Text Title TextEdit Title Text System Condition Alert Message AlertRepeat ACK ActionCurrent Reading Reset AlertNone default Not activated Activate AUXBack Abcdefghij Cancel Klmnopqrst Exit Uvwxyz PasswordBack Exit Password Enable Password Edit PasswordClock Follow the instructions in for Fixed DATE, adding Week Holiday EventEvent Type Back Exit Event Event Type Event LabelEdit Event Label Event LabelEdit Event Edit Holiday Clear EventList Event HolidayMonth January DAY Back Exit Clear HolidayList Holidays Edit Holiday OccurrenceScheduled Events Example Preset Weekend 1100 AM Sat-SunUse this page to record scheduled events Reboot System Reset, Cycle Power, RebootReset Camera Cycle Camera PowerSoftware/Language File Upload Maintenance Zoom Speed 4.2/5.8 seconds Horizontal Angle of View SpecificationsSignal Format 23X ModelsDD427 27X ModelsDD4CBW35 35X ModelsAppendix Table F. Switch Settings for SW1 Pelco P-Type ControlSpectra Switch Setting Address Table G. Switch Settings for SW1 Pelco D-Type Control 1Table G. Switch Settings for SW1 Pelco D-Type Control 2 Table G. Switch Settings for SW1 Pelco D-Type Control 3 Table G. Switch Settings for SW1 Pelco D-Type Control 4 Table G. Switch Settings for SW1 Pelco D-Type Control 5 Table G. Switch Settings for SW1 Pelco D-Type Control 6 Product Warranty and Return Information