Pelco C3463M-B manual Label Positions, Event, Alert Message, Title Text Save and Exit Cancel Help

Page 22

LABEL POSITIONS

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS> ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

DISPLAY SETUP

PRESET LABEL

ZONE LABEL ZOOM AZIMUTH/ELEVATION DIRECTION ALARM MESSAGE DATE/TIME

EVENT LABEL <LABEL POSITIONS> RESTORE FACTORY DEFAULTS

BACK

EXIT

LABEL POSITION

[ZONE LABEL-------	]
[PRESET LABEL-------	]
[ALARM --------]	[EVENT--]
[ALERT MESSAGE-------]*
<TITLE TEXT>

SAVE AND EXIT

CANCEL

HELP

NE
XX°/-XX°	XXX.X*
MM/DD/YYYY	12:00:00 AM

Labels can be placed anywhere on the monitor. This feature allows you to customize the appearance of your monitor screen.

The following labels are not set at fixed positions:

ZONE LABEL

PRESET LABEL

ALARM

ZOOM RATIO - XXX.X*

AZIMUTH†/ELEVATION‡ - XX°/-XX°

DIRECTION - NE

ALERT MESSAGE*§

TITLE TEXT

EVENT LABEL

DATE/TIME

To set a label position:

1.Use the joystick to position the cursor beside a label.

2.Press Iris Open.

3.Use the joystick to move the label up, down, left, or right.

4.Press Iris Open.

5.Repeat steps 1 to 4 to position other labels.

6.Position the cursor next to Save and Exit. Press Iris Open to save settings and exit the menu.

*This setting applies to Pressurized Spectra IV dome systems only.

†Azimuth is the pan angle from zero to 359 degrees.

‡Elevation is the tilt position from zero (horizon) to –90 degrees.

§The alert message is the warning displayed on the monitor if pressure, temperature, or dew point inside the dome reach unacceptable levels.

22	C3463M-B (2/11)

Image 22

Contents Spectra IV SL and Spectra IV SE Series Page Contents Field Align Page Description Installation Switch SettingsSW2 Switches 4 and 5 Serial Port Settings SW2 Switches 6 to 8 Baud SettingsDome Drive AddressOperation Quick Configuration GuideQuick Operation Guide Preset 95 Accessing Main Menu Extended Coaxitron or RS-485 ModeDigital Sentry System Software Endura WorkstationDigital Sentry DS Controlpoint 23X LowLight Day/Night Menu Tree Alarms Dome SettingsLine Sync Presets Password Edit the PasswordLabel Position Alert Current Reading Clear Password27X LowLight Day/Night Menu Tree Patterns ZonesPower UP Line Sync Presets Motion Detection Event Edit Event35X LowLight Day/Night Menu Tree Azimuth Elevation Zoom Custom Camera Settings Language Reset Camera Cycle Camera Power Reboot System ExitSpectra Language DIP Switch Information System InformationExit Display Setup Preset Label Display SetupRestore Factory Defaults Back Exit Event Title Text Save and Exit Cancel HelpLabel Positions Alert MessageType of Lighting Dome SettingsCamera Auto FocusLOW Light Limit Zoom LimitZoom Speed PT Focus LockAuto IR Level IR CUT FilterLow Light Focus AGC Limit Advanced Camera SettingsShutter Speed Auto IrisBacklight Compensation Auto SharpnessAuto White Balance Electronic Image StabilizationVideo Level OFF Low lux noise reduction is disabledLOW LUX Noise Reduction Field AlignMinimum Focus Distance Motion SettingsLOW Light Sharpness Auto FlipScan Speed Preset Freeze FramePark Time Limit StopsAzimuth Zero Power UP Start Time Line Sync Zoom Presets Lost ActionAuto Tracking Auto TrackingStart Time Display SetupSensitivity ZoomPower UP Action Power UPBack Exit Power UP Power UP Action Back Exit Line Sync Line Sync Phase PresetsTable C. Stored Presets by Back Box Model Back Exit Presets Preset NumberPreset 95 Select main configuration menu Preset 83 to 87 ReservedPreset 92 to 93 Scan limit stops Preset 94 Reserved Preset 96 Stop a scanAbcdefghij Cancel Klmnopqrst Uvwxyz Label for Preset Preset NumberSpace Motion Detection Enable Motion DetectionEdit Detection Areas Edit Schedule Activate Aux CommandAux Time Back Exit Patterns PatternsBack Exit Edit Zone Label ZonesBack Exit Zones Zone Number Clear Zone Back ExitWindow Blanking Enable Window Reverse Clear Window Back ExitTo set a window blanking area Reverse DisabledClear Window Blank All Above Blank All Below Blank ALL ABOVE/BLANK ALL belowBlanked Area Alarms C3463M-B 2/11 AUX Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeDwell Time Secs Edit Schedule Back Exit Back Exit Title Text Title TextEdit Title Text ACK Action AlertRepeat System Condition Alert MessageActivate AUX Reset AlertNone default Not activated Current ReadingEnable Password Edit Password PasswordBack Exit Password Back Abcdefghij Cancel Klmnopqrst Exit UvwxyzClock Follow the instructions in for Fixed DATE, adding Week Back Exit Event Event Type Event Label EventEvent Type HolidayEdit Event Label Event LabelEdit Event Holiday Clear EventList Event Edit HolidayEdit Holiday Occurrence Clear HolidayList Holidays Month January DAY Back ExitScheduled Events Example Preset Weekend 1100 AM Sat-SunUse this page to record scheduled events Cycle Camera Power Reset, Cycle Power, RebootReset Camera Reboot SystemSoftware/Language File Upload Maintenance 23X Models SpecificationsSignal Format Zoom Speed 4.2/5.8 seconds Horizontal Angle of View27X Models DD42735X Models DD4CBW35Table F. Switch Settings for SW1 Pelco P-Type Control AppendixTable G. Switch Settings for SW1 Pelco D-Type Control 1 Spectra Switch Setting AddressTable G. Switch Settings for SW1 Pelco D-Type Control 2 Table G. Switch Settings for SW1 Pelco D-Type Control 3 Table G. Switch Settings for SW1 Pelco D-Type Control 4 Table G. Switch Settings for SW1 Pelco D-Type Control 5 Table G. Switch Settings for SW1 Pelco D-Type Control 6 Product Warranty and Return Information