Pelco C3463M-B manual Dome Drive, Address

Page 9

DOME DRIVE

To install the dome drive:

1.Align the blue and red tabs with the blue and red arrows on the hinged door inside the back box.

2.Push the tabs in. Insert one side and then the other side.

3.Continue pushing on the ends of the tabs until both sides click into place (refer to Figure 2).

Figure 2. Dome Drive Installation

NOTE: When removing a dome drive that has been in use, caution should be taken to avoid direct contact with the top plate of the unit. This section of the unit will be warm to the touch when first removed from an operating unit.

4.Apply power to the Spectra IV dome system. The system will start a configuration sequence. When configuration is done, the following information is displayed:

Pelco Spectra IV SL/Spectra IV SE Version X.XX

D Address: 1

P Address: 2 Comm 2400, N, 8, 1

CONFIGURE DONE

This information will remain on the monitor until dome operation begins.

NOTE: When installing a Spectra IV dome drive in a Spectra III™ back box for the first time, a message appears. When the installation is complete, the dome drive will continue with a normal configuration sequence.

C3463M-B (2/11)

9

Image 9

Contents Spectra IV SL and Spectra IV SE Series Page Contents Field Align Page Description Switch Settings InstallationSW2 Switches 6 to 8 Baud Settings SW2 Switches 4 and 5 Serial Port SettingsAddress Dome DriveQuick Configuration Guide OperationQuick Operation Guide Extended Coaxitron or RS-485 Mode Preset 95 Accessing Main MenuEndura Workstation Digital Sentry System SoftwareDigital Sentry DS Controlpoint 23X LowLight Day/Night Menu Tree Line Sync Presets Dome SettingsAlarms Password Edit the Password27X LowLight Day/Night Menu Tree Alert Current Reading Clear PasswordLabel Position Patterns ZonesEvent Edit Event Power UP Line Sync Presets Motion Detection35X LowLight Day/Night Menu Tree Azimuth Elevation Zoom Custom Camera Settings Reset Camera Cycle Camera Power Reboot System Exit LanguageSpectra Language System Information DIP Switch InformationDisplay Setup Exit Display Setup Preset LabelRestore Factory Defaults Back Exit Label Positions Title Text Save and Exit Cancel HelpEvent Alert MessageCamera Dome SettingsType of Lighting Auto FocusZoom Speed Zoom LimitLOW Light Limit PT Focus LockIR CUT Filter Auto IR LevelLow Light Focus Shutter Speed Advanced Camera SettingsAGC Limit Auto IrisAuto White Balance Auto SharpnessBacklight Compensation Electronic Image StabilizationLOW LUX Noise Reduction OFF Low lux noise reduction is disabledVideo Level Field AlignLOW Light Sharpness Motion SettingsMinimum Focus Distance Auto FlipPark Time Preset Freeze FrameScan Speed Limit StopsAuto Tracking Power UP Start Time Line Sync Zoom Presets Lost ActionAzimuth Zero Auto TrackingSensitivity Display SetupStart Time ZoomPower UP Power UP ActionBack Exit Power UP Power UP Action Table C. Stored Presets by Back Box Model PresetsBack Exit Line Sync Line Sync Phase Back Exit Presets Preset NumberPreset 92 to 93 Scan limit stops Preset 94 Reserved Preset 83 to 87 ReservedPreset 95 Select main configuration menu Preset 96 Stop a scanLabel for Preset Preset Number Abcdefghij Cancel Klmnopqrst UvwxyzSpace Enable Motion Detection Motion DetectionEdit Detection Areas Activate Aux Command Edit ScheduleAux Time Patterns Back Exit PatternsBack Exit Back Exit Zones Zone Number ZonesEdit Zone Label Clear Zone Back ExitEnable Window Reverse Clear Window Back Exit Window BlankingTo set a window blanking area Disabled ReverseClear Window Blank ALL ABOVE/BLANK ALL below Blank All Above Blank All BelowBlanked Area Alarms C3463M-B 2/11 Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 Mode AUXDwell Time Secs Edit Schedule Back Exit Title Text Back Exit Title TextEdit Title Text Repeat AlertACK Action System Condition Alert MessageNone default Not activated Reset AlertActivate AUX Current ReadingBack Exit Password PasswordEnable Password Edit Password Back Abcdefghij Cancel Klmnopqrst Exit UvwxyzClock Follow the instructions in for Fixed DATE, adding Week Event Type EventBack Exit Event Event Type Event Label HolidayEvent Label Edit Event LabelEdit Event List Event Clear EventHoliday Edit HolidayList Holidays Clear HolidayEdit Holiday Occurrence Month January DAY Back ExitExample Preset Weekend 1100 AM Sat-Sun Scheduled EventsUse this page to record scheduled events Reset Camera Reset, Cycle Power, RebootCycle Camera Power Reboot SystemSoftware/Language File Upload Maintenance Signal Format Specifications23X Models Zoom Speed 4.2/5.8 seconds Horizontal Angle of ViewDD427 27X ModelsDD4CBW35 35X ModelsAppendix Table F. Switch Settings for SW1 Pelco P-Type ControlSpectra Switch Setting Address Table G. Switch Settings for SW1 Pelco D-Type Control 1Table G. Switch Settings for SW1 Pelco D-Type Control 2 Table G. Switch Settings for SW1 Pelco D-Type Control 3 Table G. Switch Settings for SW1 Pelco D-Type Control 4 Table G. Switch Settings for SW1 Pelco D-Type Control 5 Table G. Switch Settings for SW1 Pelco D-Type Control 6 Product Warranty and Return Information