Pelco C3463M-B manual Line Sync, Table C. Stored Presets by Back Box Model

Page 34

LINE SYNC

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS> ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA> <MOTION>

<AUTO TRACKING> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

LINE SYNC

LINE SYNC

LINE SYNC PHASE

BACK

EXIT

Line sync refers to a configurable function that allows you to synchronize all cameras within a matrix system.

Spectra IV dome systems automatically sense V-Sync input. No line sync setup is required for Pelco control systems that provide a V-Sync signal.

For matrix systems that do not output V-Sync, there are two settings for line synchronization:

ON: Adjusts the phase of the line sync to synchronize input power. Line sync phase settings range from zero to 359 degrees.

OFF (default): The dome synchronizes to the internal clock.

PRESETS

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS> ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA> <MOTION>

<AUTO TRACKING> <POWER UP> <LINE SYNC>

<PRESETS>

<PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

PRESETS
PRESET NUMBER	1
* * * PRESET NOT DEFINED * * *
<EDIT PRESET LABEL>
<EDIT PRESET SCENE>
<EDIT CAMERA SETTINGS>
<MOTION DETECTION>
<EDIT SCHEDULE>
<CLEAR PRESET>
<CLEAR CAMERA SETTINGS>
<APPLY TO GLOBAL>
BACK
EXIT
REFERENCE INFORMATION	-
AZIMUTH	-
ELEVATION	-
ZOOM RATIO	-
CUSTOM CAMERA SETTINGS	-

The model of the back box you are using limits the number of configurable presets that can be stored and retrieved in the back box memory. If you are using an older model back box, you may configure and use up to the maximum number of presets available to the dome drive. However, if the dome drive is changed, the back box model will limit the number of stored presets available to the new dome drive (refer to Table C).

Table C. Stored Presets by Back Box Model

Back Box Series	Model	Number of Stored Presets

		Spectra/Spectra SL	Spectra SE

Spectra III	BB53	99	15

Spectra IV	BB4	64	256

*This setting applies to Pressurized Spectra IV dome systems only.

34	C3463M-B (2/11)

Image 34

Contents Spectra IV SL and Spectra IV SE Series Page Contents Field Align Page Description Installation Switch SettingsSW2 Switches 4 and 5 Serial Port Settings SW2 Switches 6 to 8 Baud SettingsDome Drive AddressOperation Quick Configuration GuideQuick Operation Guide Preset 95 Accessing Main Menu Extended Coaxitron or RS-485 ModeDigital Sentry System Software Endura WorkstationDigital Sentry DS Controlpoint 23X LowLight Day/Night Menu Tree Alarms Dome SettingsLine Sync Presets Password Edit the PasswordLabel Position Alert Current Reading Clear Password27X LowLight Day/Night Menu Tree Patterns ZonesPower UP Line Sync Presets Motion Detection Event Edit Event35X LowLight Day/Night Menu Tree Azimuth Elevation Zoom Custom Camera Settings Language Reset Camera Cycle Camera Power Reboot System ExitSpectra Language DIP Switch Information System InformationExit Display Setup Preset Label Display SetupRestore Factory Defaults Back Exit Event Title Text Save and Exit Cancel HelpLabel Positions Alert MessageType of Lighting Dome SettingsCamera Auto FocusLOW Light Limit Zoom LimitZoom Speed PT Focus LockAuto IR Level IR CUT FilterLow Light Focus AGC Limit Advanced Camera SettingsShutter Speed Auto IrisBacklight Compensation Auto SharpnessAuto White Balance Electronic Image StabilizationVideo Level OFF Low lux noise reduction is disabledLOW LUX Noise Reduction Field AlignMinimum Focus Distance Motion SettingsLOW Light Sharpness Auto FlipScan Speed Preset Freeze FramePark Time Limit StopsAzimuth Zero Power UP Start Time Line Sync Zoom Presets Lost ActionAuto Tracking Auto TrackingStart Time Display SetupSensitivity ZoomPower UP Action Power UPBack Exit Power UP Power UP Action Back Exit Line Sync Line Sync Phase PresetsTable C. Stored Presets by Back Box Model Back Exit Presets Preset NumberPreset 95 Select main configuration menu Preset 83 to 87 ReservedPreset 92 to 93 Scan limit stops Preset 94 Reserved Preset 96 Stop a scanAbcdefghij Cancel Klmnopqrst Uvwxyz Label for Preset Preset NumberSpace Motion Detection Enable Motion DetectionEdit Detection Areas Edit Schedule Activate Aux CommandAux Time Back Exit Patterns PatternsBack Exit Edit Zone Label ZonesBack Exit Zones Zone Number Clear Zone Back ExitWindow Blanking Enable Window Reverse Clear Window Back ExitTo set a window blanking area Reverse DisabledClear Window Blank All Above Blank All Below Blank ALL ABOVE/BLANK ALL belowBlanked Area Alarms C3463M-B 2/11 AUX Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeDwell Time Secs Edit Schedule Back Exit Back Exit Title Text Title TextEdit Title Text ACK Action AlertRepeat System Condition Alert MessageActivate AUX Reset AlertNone default Not activated Current ReadingEnable Password Edit Password PasswordBack Exit Password Back Abcdefghij Cancel Klmnopqrst Exit UvwxyzClock Follow the instructions in for Fixed DATE, adding Week Back Exit Event Event Type Event Label EventEvent Type HolidayEdit Event Label Event LabelEdit Event Holiday Clear EventList Event Edit HolidayEdit Holiday Occurrence Clear HolidayList Holidays Month January DAY Back ExitScheduled Events Example Preset Weekend 1100 AM Sat-SunUse this page to record scheduled events Cycle Camera Power Reset, Cycle Power, RebootReset Camera Reboot SystemSoftware/Language File Upload Maintenance 23X Models SpecificationsSignal Format Zoom Speed 4.2/5.8 seconds Horizontal Angle of View27X Models DD42735X Models DD4CBW35Table F. Switch Settings for SW1 Pelco P-Type Control AppendixTable G. Switch Settings for SW1 Pelco D-Type Control 1 Spectra Switch Setting AddressTable G. Switch Settings for SW1 Pelco D-Type Control 2 Table G. Switch Settings for SW1 Pelco D-Type Control 3 Table G. Switch Settings for SW1 Pelco D-Type Control 4 Table G. Switch Settings for SW1 Pelco D-Type Control 5 Table G. Switch Settings for SW1 Pelco D-Type Control 6 Product Warranty and Return Information