Pelco C3463M-B manual Aux, Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 Mode

Page 46

AUX

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS> ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA> <MOTION>

<AUTO TRACKING> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

AUX

AUX 1 MODE	TOGGLE
DWELL TIME (SECS)	1
AUX 2 MODE	TOGGLE
DWELL TIME (SECS)	1
<EDIT SCHEDULE>
BACK
EXIT

An auxiliary output is a configurable signal from the dome back box that can trigger another device to operate. An auxiliary output can be configured to trigger from an alarm or from a controller.

An AUX 1 command from the controller will activate the relay in the dome and operate the device that is connected to the relay. The output of AUX 1 can be connected to the alarm input of a system switch to activate automatic monitor switching and recording.

An AUX 2 command from the controller will place a ground at the output of AUX 2 to operate the device that is connected to it.

The following are the available AUX mode settings:

TOGGLE (default): Changes the state of the auxiliary output every time an AUX command is received from the controller.

LATCHING: Must receive an AUX ON/AUX OFF command from the controller to turn the auxiliary output on/off.

MOMENTARY: An AUX ON command from the controller turns the auxiliary output on for the configured DWELL TIME. The auxiliary output will automatically turn off when the dwell time is finished.

EDIT SCHEDULE

The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 53) with the following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also, the Holiday feature cannot be accessed from the Edit Schedule menu.

For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on page 54.

*This setting applies to Pressurized Spectra IV dome systems only.

46	C3463M-B (2/11)

Image 46

Contents Spectra IV SL and Spectra IV SE Series Page Contents Field Align Page Description Installation Switch SettingsSW2 Switches 4 and 5 Serial Port Settings SW2 Switches 6 to 8 Baud SettingsDome Drive AddressOperation Quick Configuration GuideQuick Operation Guide Preset 95 Accessing Main Menu Extended Coaxitron or RS-485 ModeDigital Sentry System Software Endura WorkstationDigital Sentry DS Controlpoint 23X LowLight Day/Night Menu Tree Alarms Dome SettingsLine Sync Presets Password Edit the PasswordLabel Position Alert Current Reading Clear Password27X LowLight Day/Night Menu Tree Patterns ZonesPower UP Line Sync Presets Motion Detection Event Edit Event35X LowLight Day/Night Menu Tree Azimuth Elevation Zoom Custom Camera Settings Language Reset Camera Cycle Camera Power Reboot System ExitSpectra Language DIP Switch Information System InformationExit Display Setup Preset Label Display SetupRestore Factory Defaults Back Exit Event Title Text Save and Exit Cancel HelpLabel Positions Alert MessageType of Lighting Dome SettingsCamera Auto FocusLOW Light Limit Zoom LimitZoom Speed PT Focus LockAuto IR Level IR CUT FilterLow Light Focus AGC Limit Advanced Camera SettingsShutter Speed Auto IrisBacklight Compensation Auto SharpnessAuto White Balance Electronic Image StabilizationVideo Level OFF Low lux noise reduction is disabledLOW LUX Noise Reduction Field AlignMinimum Focus Distance Motion SettingsLOW Light Sharpness Auto FlipScan Speed Preset Freeze FramePark Time Limit StopsAzimuth Zero Power UP Start Time Line Sync Zoom Presets Lost ActionAuto Tracking Auto TrackingStart Time Display SetupSensitivity ZoomPower UP Action Power UPBack Exit Power UP Power UP Action Back Exit Line Sync Line Sync Phase PresetsTable C. Stored Presets by Back Box Model Back Exit Presets Preset NumberPreset 95 Select main configuration menu Preset 83 to 87 ReservedPreset 92 to 93 Scan limit stops Preset 94 Reserved Preset 96 Stop a scanAbcdefghij Cancel Klmnopqrst Uvwxyz Label for Preset Preset NumberSpace Motion Detection Enable Motion DetectionEdit Detection Areas Edit Schedule Activate Aux CommandAux Time Back Exit Patterns PatternsBack Exit Edit Zone Label ZonesBack Exit Zones Zone Number Clear Zone Back ExitWindow Blanking Enable Window Reverse Clear Window Back ExitTo set a window blanking area Reverse DisabledClear Window Blank All Above Blank All Below Blank ALL ABOVE/BLANK ALL belowBlanked Area Alarms C3463M-B 2/11 AUX Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeDwell Time Secs Edit Schedule Back Exit Back Exit Title Text Title TextEdit Title Text ACK Action AlertRepeat System Condition Alert MessageActivate AUX Reset AlertNone default Not activated Current ReadingEnable Password Edit Password PasswordBack Exit Password Back Abcdefghij Cancel Klmnopqrst Exit UvwxyzClock Follow the instructions in for Fixed DATE, adding Week Back Exit Event Event Type Event Label EventEvent Type HolidayEdit Event Label Event LabelEdit Event Holiday Clear EventList Event Edit HolidayEdit Holiday Occurrence Clear HolidayList Holidays Month January DAY Back ExitScheduled Events Example Preset Weekend 1100 AM Sat-SunUse this page to record scheduled events Cycle Camera Power Reset, Cycle Power, RebootReset Camera Reboot SystemSoftware/Language File Upload Maintenance 23X Models SpecificationsSignal Format Zoom Speed 4.2/5.8 seconds Horizontal Angle of View27X Models DD42735X Models DD4CBW35Table F. Switch Settings for SW1 Pelco P-Type Control AppendixTable G. Switch Settings for SW1 Pelco D-Type Control 1 Spectra Switch Setting AddressTable G. Switch Settings for SW1 Pelco D-Type Control 2 Table G. Switch Settings for SW1 Pelco D-Type Control 3 Table G. Switch Settings for SW1 Pelco D-Type Control 4 Table G. Switch Settings for SW1 Pelco D-Type Control 5 Table G. Switch Settings for SW1 Pelco D-Type Control 6 Product Warranty and Return Information