Samson UHF Series One owner manual Guided Tour UT1L / UT1G

Page 7

Guided Tour - UT1L / UT1G

4

LOW MID HIGH

BATT AUDIO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

2

 

 

3

 

 

 

 

 

 

 

 

1:Input connector - The input device is connected here. The UT1L is supplied with either a lavalier or headset microphone (connected via a Switchcraft mini-XLR jack), while the UT1G is supplied with a permanently connected 1/4" jack cable.

2:Battery level meter - This set of three multicolor LEDs indicates relative battery power, indicating whether the installed battery is at low (red), mid (yellow) or high (green) strength. One of these will light whenever the UT1L or UT1G is powered on (see #8 on the next page). When the red “low” indicator lights, RF performance is degraded and the battery needs to be replaced.

3:Audio on-off switch - When set to the “on” position, audio signal is transmitted. When set to the “off” position, the audio signal is muted. Because the carrier signal remains during muting, no “pop” or “thud” will be heard. Note that turning this off does not turn off the transmitter power— it is simply a way to temporarily mute the transmission of audio signal. If you don’t plan on using the transmitter for extended periods, turn off the transmitter power by using the power on-off switch (see #8 on the next page).

4:Belt clip - Use this clip to fasten the UT1L or UT1G to a belt. The position of the clip can be rotated to the desired position after loosening its

center screw or can be removed entirely by removing the center screw.

ENGLISH

5:Battery cover release - Slide the release lever down to open the UT1 battery cover.

6:Antenna - This permanently attached transmitter “pig tail” antenna should be fully extended for normal operations. See the “Setting Up and Using the UM1 System” section on page 8 in this manual for more infor- mation about antenna positioning.

7:Battery holder - Insert a standard 9-volt alkaline battery here, being sure to observe the plus and minus polarity markings shown. We recommend the Duracell MN 1604 type battery. Although rechargeable Ni-Cad batteries can be used, they do not supply adequate current for more than four hours. WARNING: Do not insert the battery backwards; doing so can cause severe damage to the UT1L / UT1G and will void your warranty.

UT1

5

SAMSON

6

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents UM1 Table of Contents System Features Introduction / System FeaturesSamson QE headset Samson QV headset System FeaturesSamson Qmic dynamic Samson Guided Tour UM1Headphones output Connect a Guided Tour UT1L / UT1G Sams on Microphone Input Level control trimpot Guided Tour UH1Setting Up and Using Your UM1 System Setting Up and Using Your UM1 System Setting Up and Using Your UM1 System Francais Samson Qmic dynamique Samson QE serre-tête Samson QV serre-têteTé moins dactivité des ré cepteurs A/B Visite guidée UM1Connecteur dalimentation Ce con Visite guidée UT1L / UT1G Sams on Visite guidée UH1 Paramétrage et utilisation du système UM1 Paramétrage et utilisation du système UM1 Paramétrage et utilisation du système UM1 Deutsche Samson Qmic Dynamikmikrofon Samson QE Kopfbügelmikrofon Samson QV KopfbügelmikrofonBedienelemente UM1 Frequenzzuordnung der Empfangskanäle Deutsche Bedienelemente UT1L / UT1GSams on Deutsche Bedienelemente UH1Aufbau und Betrieb des UM1 Aufbau und Betrieb des UM1 Aufbau und Betrieb des UM1 Espanol Samson Qmic dinámico Samson QE de auricular Samson QV de auricularRecorrido guiado UM1 Salida no balanceada* Utilice este Recorrido guiado UT1L / UT1G Sams on Control de nivel de entrada de micró fono ajuste Recorrido guiado UH1Ajuste y utilización de su sistema UM1 Ajuste y utilización de su sistema UM1 Espanol Appendix a UT1L Multipin Wiring Guide and Chart System Specifications SpecificationsFCC Rules and Regulations
Top Page Image Contents