LG Electronics LRN3040N Series Connecting E-SATA device, Connecting Network, Connecting IP Camera

Page 13

Installation

USB External device

LAN connection

13

Connect the external device to the USB port. (Example: External HDD or other external storage.)

Mouse

Connect the USB mouse to operate the system.

Connecting E-SATA device

You can use E-SATA storage for data back-up or recording.

E-SATA device connection
	2		4
ARM
OUT			USB		DC 48 V
OUT			5 V	0.5 A
1 2 G			5 V	0.5 A
1 2 G
LAN	1	CAM	3	E-SATA

Connecting Network

You can control and monitor the system via network. With the remote control (monitoring), you can change the system configuration or monitor the image via network. After the installation, check the network settings for the remote control and monitoring work.

Network connection
485	IN	OUT			5 V	0.5 A
- + 1 2 3 4 G 1 2 G					5 V	0.5 A
- + 1 2 3 4 G 1 2 G
		LAN	1	CAM	3	E-SATA
				Router		Broadband
				Router		Service
						Service

Connect the LAN port to an available 10/100/1000 base-T port with a straight ethernet cable (not supplied). The NET indicator on the front panel will be lit.

IP Camera connection

Connect the IP camera. After the installation, check the IP camera settings on the setup menu.

Automatic network configuration

The system can automatically obtain and configure the network interface via DHCP.

Manually configure network

The system may be manually configured by assigning an IP address, subnet mask, gateway and DNS.

NOTE

This unit can be supported IPv4 and IPv6 network.

Connecting IP Camera

Connect the IP Camera for Plug and connect.

NOTE

•To use IP Camera for plug and connect port, should be set to DHCP. It will be changed to Static automatically by the system.

•When you connect a camera, you should set the administrator ID and password of camera as below table.

ID	Password

admin	admin

root	root

root	4321

•The IP camera must be supported ONVIF.

IP Camera connection
	2		4
ALARM
OUT			USB		DC 48 V
OUT			5 V	0.5 A
4 G 1 2 G			5 V	0.5 A
4 G 1 2 G
LAN	1	CAM	3	E-SATA

3

Installation

Image 13

Contents Network Video Recorder Contact office for compliance of this product Regulatory Information FCC PartEEE Compliance with Directive. for Turkey only Disposal of your old applianceDisposal of waste batteries/accumulators Safety warnings and Cautions Safety Information Contents Emergency Using the playback control menu Using the Protect functionOutput Buzzer Group Authority UserAccessories FeaturesIntroduction Rear Panel Front PanelRemote Control Connections PrecautionsBasic Connection Overview Line inputConnecting Audio device Connecting Display deviceConnecting USB device Connecting Network Connecting E-SATA deviceConnecting IP Camera Connecting Alarm Input and Alarm Output Connecting LKD1000 ControllerAlarm Input Data Transmission/ReceptionAlarm Output Installing the Hard Disk DriveAlarm device Terminal NoRecommended HDD Replacing the Hard Disk DriveSystem Shutdown System OperationMain Monitor Screen Moving the Channels Position Selecting the Split modeChanging the order of cameras To Register Preset Positions Preset SettingsChanging to a Picture in a Preset Position To Clear the Preset PositionTo Tour The Preset Positions Using the Digital Zoom functionSetup for PTZ Cameras Export the recorded dataViewing the System Log List Using a mouse to set a menu Configuration menuViewing System Information Use the left mouse buttons to set the menuSetting the Menu Using the Remote Control Buttons System settingsProperties RemoteTCP/IP How to register Ddns host nameNetwork Network Streaming When you want to change Ddns host nameDate/Time Controller Instant Backup UpdateUp to 2 TB Daily/Weekly backupMotion Setting Device settingsStream Setting Audio/Sensor settingTo register the IP device manually To register the IP device automaticallyStorage Display settingsSequence Normal Schedule Recording Record settingsCopying from the Scheduled Data of the Channel Copying the Recording ScheduleCopying from the Scheduled Data of the Day Time you want to record. The color of the time block isSensor Event settingsMotion NotificationEmergency MailWhich you want to enable this system e.g. lgecommunity or User settingsOutput Group Authority BuzzerUser Setup Wizard settingsStep Set date and time Instant Recording OperationInstant Playback Using the calendar icon to select a dateSearch and Playback Date and Time SearchBookmark/Protect Search Export SearchFunctions Available During Playback Remote ControlButton Stops playbackUsing the Protect function Using the playback control menuHow to select Protect section How to release the Protect sectionSymptoms Cause & Solution You can reboot the system as follows If you observe any of the following symptomsRecommended USB Memory list Recommended DevicesRecommended External Device list Maker Model Name CapacityExport Configuration Import/Export Device Instant backupSupported function list for device Supported IP Camera Audio/Video CodecTimezone name Time zonesTimezone 1st level 2nd level 3rd level Default Value Factory Default Factory Default Configuration SettingsYYYY/MM/DD Date Current DateDisplay Day Current day of the week Event OFF YESGroup ID Model LRN3040N Series Specifications