LG Electronics LRN3040N Series owner manual Event settings, Sensor, Motion, Notification

Page 33

Installation 33

Sensor

Settings concerning sensor recording.

•CH: Displays the channel number.

•Prealarm: Specify the pre-event recording time. When the Event signal is detected, the system recordes the data before the event during the setting time.

•Postalarm: Specify the post-event recording time. When the Event signal is detected, the system recordes the data after the event during the setting time.

Motion

Settings concerning motion recording.

•CH: Displays the channel number.

•Prealarm: Specify the pre-event recording time. When the Event signal is detected, the system recordes the data before the event during the setting time.

•Postalarm: Specify the post-event recording time. When the Event signal is detected, the system recordes the data after the event during the setting time.

NOTE

The Prealarm recording time may shorten depending on the setting and recording status of camera.

Event settings

Sensor

3

Installation

•In: Displays the number of the ALARM-IN terminal.

•Sensor Type: The sensor state can be set to either N.O. (Normally Open) or N.C. (Normally Closed).

•Camera: Select the camera channel when the sensor event is occurred.

•Relay Output: Select the alarm (relay) output number for the RELAY-OUT terminal for the output alarm (relay) signal.

•Preset: Select the preset number. When the input is activated, the camera moves to the selected preset position and the picture of the camera in that position appears on the monitor.

Notification

Marks up when you want to activate the selected option. If the selected notification option is activated, the device will notify the user about the information of selected option by E-mail.

•Sensor On: Sends an e-mail when a sensor has occurred.

•Motion Detection: Sends an e-mail when a motion detection has occurred.

•Admin Password Changed: Sends an e-mail when the administrator password has been changed.

•Power On/Off: Sends an e-mail when power is on or off.

•Disk Full: Sends an e-mail when the HDD has fully recorded.

Image 33

Contents Network Video Recorder Contact office for compliance of this product Regulatory Information FCC PartDisposal of your old appliance EEE Compliance with Directive. for Turkey onlyDisposal of waste batteries/accumulators Safety warnings and Cautions Safety Information Contents Emergency Using the playback control menu Using the Protect functionOutput Buzzer Group Authority UserFeatures AccessoriesIntroduction Rear Panel Front PanelRemote Control Connections PrecautionsBasic Connection Overview Line inputConnecting Display device Connecting Audio deviceConnecting USB device Connecting E-SATA device Connecting NetworkConnecting IP Camera Connecting Alarm Input and Alarm Output Connecting LKD1000 ControllerAlarm Input Data Transmission/ReceptionAlarm Output Installing the Hard Disk DriveAlarm device Terminal NoRecommended HDD Replacing the Hard Disk DriveSystem Operation System ShutdownMain Monitor Screen Selecting the Split mode Moving the Channels PositionChanging the order of cameras To Register Preset Positions Preset SettingsChanging to a Picture in a Preset Position To Clear the Preset PositionTo Tour The Preset Positions Using the Digital Zoom functionSetup for PTZ Cameras Export the recorded dataViewing the System Log List Using a mouse to set a menu Configuration menuViewing System Information Use the left mouse buttons to set the menuSetting the Menu Using the Remote Control Buttons System settingsProperties RemoteHow to register Ddns host name TCP/IPNetwork When you want to change Ddns host name Network StreamingDate/Time Controller Instant Backup UpdateUp to 2 TB Daily/Weekly backupMotion Setting Device settingsStream Setting Audio/Sensor settingTo register the IP device manually To register the IP device automaticallyDisplay settings StorageSequence Normal Schedule Recording Record settingsCopying from the Scheduled Data of the Channel Copying the Recording ScheduleCopying from the Scheduled Data of the Day Time you want to record. The color of the time block isSensor Event settingsMotion NotificationEmergency MailWhich you want to enable this system e.g. lgecommunity or User settingsOutput Group Authority BuzzerSetup Wizard settings UserStep Set date and time Instant Recording OperationInstant Playback Using the calendar icon to select a dateSearch and Playback Date and Time SearchBookmark/Protect Search Export SearchFunctions Available During Playback Remote ControlButton Stops playbackUsing the Protect function Using the playback control menuHow to select Protect section How to release the Protect sectionSymptoms Cause & Solution You can reboot the system as follows If you observe any of the following symptomsRecommended USB Memory list Recommended DevicesRecommended External Device list Maker Model Name CapacityExport Configuration Import/Export Device Instant backupSupported function list for device Supported IP Camera Audio/Video CodecTime zones Timezone nameTimezone 1st level 2nd level 3rd level Default Value Factory Default Factory Default Configuration SettingsYYYY/MM/DD Date Current DateDisplay Day Current day of the week Event OFF YESGroup ID Model LRN3040N Series Specifications