LG Electronics LRN3040N Series Device settings, IP Device, Motion Setting, Stream Setting

28Installation

Device settings	-- Sensor: Select the sensor number on the drop-down list.
	-- In Use: Marks up when you want to activate the sensor.
	-- Sensor Type: Select the sensor type.
	-- Relay Output: Select the relay output number
	on the drop-down list.

3

Installation

IP Device	--	Relay Type: Select the relay type.
	--	Control Duration: Enter the relay time.
	Motion Setting
	You can configure this option when you select to [LGE] on the
	[Driver] option. Select [Motion] tab of the [Setup] window.
	1.	Click the [Add] button. The motion detect window is
		displayed. You can add the five windows maximum for
		motion detection area.
	2.	Set the [Sensitivity] option.
	3.	Click the edge or corner of the window box to adjust the
		window size for motion detection.
	4.	Click the [Save] button to save the settings.
	Stream Setting

•CH: Displays the channel number.

•Name: Enter the channel name.

•Model Name: Displays the model name of IP device.

•MAC: Displays the Mac address of IP device.

•IP: Displays the IP address of IP device.

•HTTP Port: Enter the HTTP port number. HTTPS is not supported.

• / : You can see other options (Driver, Profile1, Profile2, RTSP Port, RTP Mode, Audio Recording) to click button. To return previous options, click button.

•Driver: Selects the IP camera driver from the drop-down list.

•Profile1: Select the camera stream on the drop-down box for recording.

•Profile2: Select the camera stream on the drop-down box for streaming. For smooth live playback, the resolution of [Profile2] set lower than resolution of [Profile1].

NOTE

If you select to [LGE] on the [Driver] option, select the [Stream] tab. When you select [ONVIF] on the [Driver] option, you can configure the stream setting only. In case of [AXIS], the [Bitrate] and the [Compression] options are activated only.

-- Stream (LGE only): Select the video stream.

-- In Use (LGE only): Click to activate the stream function.

-- Video Codec: Select the video mode (Codec) from the dropdown list.

-- Resolution: Select the output image size of the camera.

-- Frame Rate: Set the frame rate of the image.

-- GOP: It means “Group of Pictures”. The higher the GOP, the better is the video quality of the camera. Edit the value of GOP from 1 to 30. This setting is valid for H.264 video format only.

NOTE

It recommended that you set the [GOP] value same as [Frame Rate].

• When you select full screen mode on the [split mode],	-- GOV (ONVIF only): It means “Group of VOPs”. The VOP is an
	image frame in the MPEG-4 video stream. Edit the value of
[Profile1] operate for streaming automatically.
	GOV from 1 to 30.
• When CPU usage occupies more than 90% and then 1 minute
	-- Quality: Select the Quality.
goes by, connection of [Profile2] is limited for the stability of
	-- Stream Quality (LGE only): If the [Quality] option set to VBR,
system.
	this option is displayed. Select the stream quality from the
• RTSP Port: Enter the RTSP port number.	drop down box, the camera supports five types. (Highest,
	High, Medium, Low and Lowest)
• RTP Mode: Select the RTP mode from drop-down list.
	-- Bitrate: If the [Quality] option set to CBR, this option is
• Audio Recording: Check the audio recording option.
	displayed. Edit the bit rate value from 256 kbps to 10 240
• Setup: Click the check box of the desired channel and then	kbps.
press the [Setup] button. The setup window will be displayed.	-- Compession (AXIS only): Enter the compression ratio of
Audio/Sensor setting	video. The lower value you set up, the higher definition
You can configure this option when you select to [LGE] on the	picture you get.
	• Delete: Click the check box of the desired channel and then
[Driver] option. Select [Audio/Sensor] tab of the [Setup] window.
-- Audio In: Click the check box if you want to send the audio	press the [Delete] button. Registered channel of IP Camera will
	be deleted.
from the microphone input connector.
-- Audio Type: Select the codec when you send the audio from
the microphone input connector.
-- Audio Out: Click the check box to output the audio from the
speaker.