Panasonic HD3700H operating instructions ∑ Pre-read editing, Sd Sdi Sd Sdi Out

Page 16

HOME menu

∑Pre-read editing

(1)Set the pre-read function to ON by pressing the F key and F11 key (PREAD A) or F12 key (PREAD V) together.

PREAD V

ON

PREAD A

ON

(2)Perform the connections for pre-read editing as shown in the figure below.

(3)Proceed with pre-read editing in the desired insert editing mode.

(4)Restore the original connections upon completion of the editing.

(5)Press the F11 or F12 key to set the pre-read function to OFF.

(6)Check that there are no loop connections.

ONoteN

During pre-read operations, the SD SDI MONITOR and AUDIO MONITOR connectors function as monitoring connectors, and the input signals are output from the IN point to the OUT point in their original state.

Further, the preread monitor function will not work when the monitor MIX function has been set to ON. To use the function, set MIX to OFF.

Video Source

Audio Source

Digital video output

VideoDigital video input

Switcher

SD SDI IN

SD SDI OUT

Digital

HD

SD

1

2

3

WFM

IN

OUT1

IN

OUT1

OUT3

REF IN

VIDEO OUT

SD SDI

HD SDI

~AC IN

FUSE

Audio

or

125V 5A

ON

ON

(SUPER)

75Ω

75Ω

2 4

6 8

ACTIVE

ACTIVE

SD

CH

CH

INPUT

CH

CH

THROUGH

OUT2

THROUGH

OUT

OFF

OFF

1 3

5 7

2

Mixer

analog

2 4

6 8

MONITOR

HD

SD

SPARE

MONITOR

(SUPER)

CH 1 3 CH

OUTPUT

CH 5 7 CH

audio

REMOTE

REMOTE

REMOTE

(SUPER)

RS-232C

V/A

REF OUT

DIGITAL AUDIO

input

IN

OUT

IN/OUT

CONTROL

PARALLEL

IN/OUT

CONTROL

(50P)

PANEL

		AUDIO IN			TIME CODE
PUSH H 1	PUSH H 2	PUSH H 3	PUSH H 4	PUSH H 5	PUSH N	OUT

			AUDIO OUT
SIGNAL	CH 1	CH 2	CH 3	CH 4
GND

		MONITOR
CUE	L	R

Digital or analog audio output

Connections for pre-read editing

– 16 –

Image 16

Contents Operating Instructions SoftwareContents Test IC Card Error LOG Menu screen transitions Multi CUE Multi CUE SET UP Assemble Manual Edit S T A G Turning on the power Turn on the power Home menu is displayedHome menu displays ∑ Display lampsCH1 AES CH1 SERSD Free HD FreeDual ∑ Setting mode display area ∑ Remaining tape time∑ User file display ∑ Time code displays∑ Setting the initial value for the time code 00 00 00∑ Setting and checking the cue time Press the 4 cursor key Cue time now appears in reverse videoHome menu This menu is displayed by pressing the following key HomeKey Key designation Description Free ALL∑ Pre-read editing SD SDI SD SDI OUTHome SET UP menu This menu is displayed by pressing the following keys HomeField FRAME11Fine CoarseAfter pressing the F11 key, turn the Adjust control PrerollF12 Still F13 Stby OFFPress the ENT key. The setting is now entered ∑ ReferenceCenter cursor key Cursor key∑ Programmed play function Video in menu This menu is displayed by pressing the following keyINT SG RampMULT-BST BlackVideo OUT HD menu BLACK.L F3 PRConvert Video OUT HD SET UP menu This menu is displayed by pressing the following keysSerial SYS Phase Line ConvInterp OFFVideo OUT HD SET UP State menu EemodeVideo OUT SET UP State menu ∑ Selecting the TAPE/EE output signalsVideo OUT SD menu Transfers the VTR to the Video OUT SD SET UP Composite Transfers the VTR to the Video OUT SD SET UP SDI menuCmpst Menu screenVideo OUT SD SET UP Composite menu Comb FIL1 SYS SCSYS H Line BLK2Video OUT SD SET UP Cmpst State menu Through The E-E through mode AV minimum delay modeOr Audio OUT F8 F12 Is established∑ Selecting the TAPE/EE output signals Video OUT SD SET UP SDI menu With the 480/59.94p format1 Adjustment can be made from FINE/COARSEWith the 480/59.94i format With the 576/50i format1Video OUT SET UP Line BLK video output line blanking menu ALL onALL OFF Line BLK∑ Setting the line blanking Move the cursor and select the lines to be blankedVideo OUT SD SET UP SDI State menu Video OUT SET UP State menu Video OUT Convert menu HdtosdSdtohd HdtohdVideo OUT Convert Hdtosd menu FitvFith Standard Wide NarrowConverter Video OUT Convert Sdtohd menuSelects the frequency bandwidth of the up-converter output Controls the enhancement adjustment of the converter output Video OUT Convert Hdtohd menuAudio in menu PCM CUECH-MIX Audio in PCM Input Select menu Digital AnalogDigital Selects the signals of the analog CH2 input CH6 Selection is made in line with the CH5 setting usingF10 CH-6 ANA CH2Audio in CUE Input Select menu Tape Mixes the playback signalsNo mixing Audio in SET UP menu This menu is displayed by pressing the following keys AudioTone ∑ Switching the audio level meter scaleFr in increments of 1/10th of a frame Audio in CH-MIX Select menu SelectCH-MIX on CH-MIX OFF∑ Mix-and-record Sound output based on VTR’s mode and F6, F7 key statuses ONotesNAudio OUT menu Monitor SDI AsignAudio OUT Monitor menu Shtl MoniVAR ADDAudio OUT SET UP menu F1 A/V Phase JOG ProcVAR Proc PB FadePCM The style is set to the normal PCM audio mode Data The style is set to the data mode compressed audioTransfers the VTR to the Audio OUT SET UP State menu Dolby-E∑ Fade function Audio OUT SET UP State menu F3-F7Video OUT SET UP State menu Audio OUT SDI Asign menu CH1T4 SdtosdTC/CHR menu INT EXT LTCLTC VTCTC.UB TC.STIntense Time code displays CTL1 Control signal ∑ Changing the superimposing position∑ Time code displays and VTR’s operating modes TCG∑ Error information displays Table of user bit settings