Panasonic HD3700H operating instructions ∑ Switching the audio level meter scale, Tone

Page 54

AUDIO IN SET UP menu

Key

Key designation

 

Description

F1

INT SG MD

For selecting the internal audio test signal.

 

 

TONE:

Reference level sinusoidal waves are output.

 

 

SILENCE: A signal tone is not output. (Mute signals are output.)

 

 

 

 

F2–F5

——

 

 

F6

PEAK HOLD

For holding the peak recording and playback levels on the

 

For setting the peak hold.

display.

 

 

 

ON: Peak level is held.

 

 

OFF: Peak level is not held.

 

 

 

F7

SCALE

For switching the scale of the audio level meter on display to

 

For switching the level

standard scale or fine scale.

 

meter scale.

FINE: Scale in 0.2 dB incremens. (j24dB to j15dB)

 

 

FULL: Standard scale (j¶ to j0dB)

 

 

Refer to “Switching the audio level meter scale” (on this page).

 

 

 

F8

EXIT

Returns the VTR to the AUDIO IN menu screen.

F9

DATA ADV°1

0–1 Fr (in increments of 1/10th of a frame):

 

 

The amount by which the data is to be advanced when the

 

 

digital audio input/output format is in the data mode can be set

 

 

in increments of 1/10th of a frame. (When “0” is set, the

 

 

amount is set to the default setting inside the VTR.)

 

 

 

F10

STYLE°

This menu item can be set by pressing the F10 key together with

 

For setting the digital

the F key.

 

audio input/output data

PCM: The format is set to the regular PCM audio mode.

 

format.

DATA: The format is set to the data mode (compressed audio:

 

 

 

Dolby-E°2).

F11–F13

——

 

 

°1The data mode is operational only in the 4-channel audio versions of the 1080/59.94i and 720/59.94p system formats.

°1The data advance amount and data style can be set on both the AUDIO IN SETUP menu and AUDIO OUT SETUP menu. If the setting is updated on one menu, it will be updated on the other menu as well. Furthermore, these settings cannot be performed on a channel by channel basis.

°2“Dolby” and the double-D symbol Î are trademarks of Dolby Laboratories Licensing Corporation.

∑Switching the audio level meter scale

≥If the audio level is adjusted below j24 dB in the FINE mode, the ; mark is displayed; if it is adjusted above j15 dB, the : mark is displayed.

– 54 –

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Operating Instructions SoftwareContents Test IC Card Error LOG Menu screen transitions Multi CUE Multi CUE SET UP Assemble Manual Edit S T A G Turning on the power Turn on the power Home menu is displayedCH1 AES Home menu displays∑ Display lamps CH1 SERHD Free SD FreeDual ∑ User file display ∑ Setting mode display area∑ Remaining tape time ∑ Time code displays∑ Setting the initial value for the time code 00 00 00∑ Setting and checking the cue time Press the 4 cursor key Cue time now appears in reverse videoHome menu This menu is displayed by pressing the following key HomeKey Key designation Description Free ALL∑ Pre-read editing SD SDI SD SDI OUTHome SET UP menu This menu is displayed by pressing the following keys HomeFine FieldFRAME11 CoarseF12 Still After pressing the F11 key, turn the Adjust controlPreroll F13 Stby OFFCenter cursor key Press the ENT key. The setting is now entered∑ Reference Cursor key∑ Programmed play function Video in menu This menu is displayed by pressing the following keyMULT-BST INT SGRamp BlackVideo OUT HD menu F3 PR BLACK.LConvert Video OUT HD SET UP menu This menu is displayed by pressing the following keysInterp Serial SYS PhaseLine Conv OFFVideo OUT HD SET UP State menu EemodeVideo OUT SET UP State menu ∑ Selecting the TAPE/EE output signalsVideo OUT SD menu Cmpst Transfers the VTR to the Video OUT SD SET UP CompositeTransfers the VTR to the Video OUT SD SET UP SDI menu Menu screenVideo OUT SD SET UP Composite menu SYS H Comb FIL1SYS SC Line BLK2Or Audio OUT F8 F12 Video OUT SD SET UP Cmpst State menuThrough The E-E through mode AV minimum delay mode Is established∑ Selecting the TAPE/EE output signals Video OUT SD SET UP SDI menu With the 480/59.94i format With the 480/59.94p format1 Adjustment can be made fromFINE/COARSE With the 576/50i format1ALL OFF Video OUT SET UP Line BLK video output line blanking menuALL on Line BLK∑ Setting the line blanking Move the cursor and select the lines to be blankedVideo OUT SD SET UP SDI State menu Video OUT SET UP State menu Sdtohd Video OUT Convert menuHdtosd HdtohdFith Video OUT Convert Hdtosd menuFitv Standard Wide NarrowVideo OUT Convert Sdtohd menu ConverterSelects the frequency bandwidth of the up-converter output Controls the enhancement adjustment of the converter output Video OUT Convert Hdtohd menuAudio in menu CUE PCMCH-MIX Audio in PCM Input Select menu Analog DigitalDigital F10 CH-6 Selects the signals of the analog CH2 inputCH6 Selection is made in line with the CH5 setting using ANA CH2Audio in CUE Input Select menu Mixes the playback signals TapeNo mixing Audio in SET UP menu This menu is displayed by pressing the following keys Audio∑ Switching the audio level meter scale ToneFr in increments of 1/10th of a frame CH-MIX on Audio in CH-MIX Select menuSelect CH-MIX OFF∑ Mix-and-record Sound output based on VTR’s mode and F6, F7 key statuses ONotesNAudio OUT menu Monitor SDI AsignAudio OUT Monitor menu VAR ShtlMoni ADDAudio OUT SET UP menu VAR Proc F1 A/V PhaseJOG Proc PB FadeTransfers the VTR to the Audio OUT SET UP State menu PCM The style is set to the normal PCM audio modeData The style is set to the data mode compressed audio Dolby-E∑ Fade function Audio OUT SET UP State menu F3-F7Video OUT SET UP State menu Audio OUT SDI Asign menu CH1T4 SdtosdTC/CHR menu LTC INTEXT LTC VTCTC.ST TC.UBIntense ∑ Time code displays and VTR’s operating modes Time code displays CTL1 Control signal∑ Changing the superimposing position TCG∑ Error information displays Table of user bit settings
Top Page Image Contents