AMX manual MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box

Page 30

MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box

Open the Battery Compartment by pressing down on the Battery Compartment Latch and then pulling the cover outwards.

Press the Cradle Activation pushbutton (the small recessed white button located near the pins in Battery Slot #2) to make the MVP Support Cradle rise upwards. The MVP Support Cradle must be angled upward to allow removal of the faceplate.

Disconnect the 2-pin mini-Phoenix connector from the side of the docking station to remove power from the unit. Removing power from the MVP-WDS at this point maintains the support cradle in this angled position.

5.Slide the silver Faceplate over the angled Support Cradle, toward the Security Release Pushbutton’s circuit board on the MVP-WDS.

6.Gently press the silver faceplate down and under the Security Latch until it rests against the Mounting Tabs of the MVP-WDS main unit.

Be sure to snap the Faceplate Connectors into their respective Latches (located along the bottom rim of the faceplate - see FIG. 20 on page 20).

Verify that the two faceplate security screw holes on both the Faceplate and the main

MVP-WDS unit are properly aligned.

7.Insert and secure the two #6-32 Faceplate Security Screws into the top rim of the Faceplate using a screwdriver.

8.Apply power to the MVP-WDS by connecting the terminal end of the power cable to the power supply.

9.Press the Cradle Activation pushbutton to cause the MVP Support Cradle to angle backwards and lie flush against the main unit.

10.Remove the two adhesive plastic Die Cut Foam covers (60-5965-47) from the strip included within the Installation Kit bag.

11.Adhere these two plastic Die Cut Foam covers into the two notches where the #6-32 Faceplate Security Screws are located (FIG. 18 on page 19).

12.Reapply power to the unit.

Refer to the Connecting a Power Supply section on page 13 for more information.

13.Install the WDS back into its previous location.

Refer to the Installation section on page 4 for more information.

24

MVP-WDS Wall Docking Station for MVP Panels

Image 30
Contents MVP-WDS AMX Limited Warranty and Disclaimer FCC Information Page Table of Contents Page MVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box OverviewSpecifications MVP-WDS SpecificationsMVP-WDS docking station connector locations LED IndicatorsInstallation Installing the CB-MVPWDS Conduit BoxRemoving the MVP-WDS Faceplate MVP Support CradleSecurity Latch Faceplate Securing Latches Faceplate Connectors Installing the MVP-WDS in a CB-MVPWDS Conduit Box Installing the MVP-WDS Using Expansion Clips MVP-WDS Wall Mount cutout dimensions using expansion clips Replacement drywall clip sets cab be ordered from AMX Screws not included Connecting a Power Supply Powering the MVP-WDSReplacing the Faceplate on the MVP-WDS Using the 3.5mm mini-Phoenix Connector for Power Connecting and Using USB Input Devices on the StationsInterface Connector Pins and Functions Securing an MVP Panel to an MVP-WDSRemoving an MVP Panel from an MVP-WDS Unsecured MVP removal from an MVP-WDSSecured MVP removal from an MVP-WDS Installing and Charging Batteries in the Docking Stations Installing MVP-BP Batteries Into the MVP-WDSUndock-USER String Installing the MVP-WDS-SK Silver Conversion Kit Removing the original faceplateSecurity Latch Faceplate securing latches Gap opening Installing the new conversion kit’s pivot unit components Removing the attached circuit boards a & BInstalling the new silver faceplate Installation of silver cradle pivot and battery coverMVP-WDS Wall Docking Station & CB-MVPWDS Conduit Box Upgrading the Docking Station Firmware Prepare the Docking Station for firmware transfer via USBUpgrade the Docking Station firmware via USB Default Modero panel value isDevice and System values Upgrading the Docking Station Firmware Page It’s Your World Take Control