Blaupunkt MP76 Calibrating DNC, Switching DNC off, Starting the DNC calibration

Page 45

DNC

DNC

Dynamic Noise Covering

DNC allows for raising a volume when driv- ing that is considered pleasant for a non- driving vehicle.

The increase differs according to frequency ranges, dependent upon the noise develop- ment of the vehicle.

Hence, volume and sound remain at a pleasant level even with changing noise developments. Short-term noises, such as those while crossing railways, are not con- sidered.

Calibrating DNC

A calibration via the measurement micro- phone is required for vehicle-speciﬁc op- eration. The DNC calibration should be per- formed after the DSA calibration. Before the calibration, you should permanently attach the calibration microphone with the supplied Velcro tape near the console, but not in the ﬂoor area, at droning points or at the heating/ventilation.

The opening of the calibration microphone must point to the direction of the passen- ger compartment. The calibration should be performed at a quiet location with the engine switched off. The doors, windows and sunroof must remain closed, and you should be seated in the driver’s seat.

Starting the DNC calibration

Press and hold the AUDIO button : for longer than two seconds.

Press the softkey 5 with the display label "DNC".

Press the softkey 5 with the display	ENGLISH
Press the softkey 5 with the display
label "ADJUST".
A countdown is running on the display. Af-
ter the countdown expires, the calibration
is performed.

Press the OK joystick 8or the AUDIO button :to exit the menu.

Switching DNC off

To deactivate the DNC,

press and hold the AUDIO button : for longer than two seconds.

Press the softkey 5 with the display label "DNC".

Press the softkey 5 with the display label "OFF".

"DNC OFF" appears on the display. To reactivate the DNC,

select a DNC increase (DNC1 - DNC5).

Press the OK joystick 8or the AUDIO button :to exit the menu.

The settings are saved.

97

Image 45

Contents Bremen MP76 Page Slot for MMC/SD Volume CD modeDisplay Adjusting high-pass ﬁlters for Front/rear MP3 modeRepeating individual tracks or TMC for dynamic navigation SystemsSafety note Road safetyInstallation Disposal of old unitTheft protection Activating/deactivating demo modeDetachable control panel Detaching the control panelSwitching on/off using button Switching on/offSwitching on/off using the vehicle ignition Attaching the control panelSetting the power-on volume VolumeRisk of injury MuteActivating the navigation audio Navigation audioAdjusting the bass Sound and volume relationshipAdjusting the treble Adjusting the navigation minimum volumeAdjusting the front/rear volume ratio fader Setting the left/right volume ratio balanceTo adjust the balance, press the Audio button To adjust the fader, press the Audio buttonSetting the button illumination colour Adjusting the viewing angleAdjusting the display brightness DisplaySetting the display illumination colour Selecting a preset colourMixing a colour for the display illumination Inverting display contents Radio mode Adjusting the tunerSetting the number of antennas Selecting static/dynamic radio mode FM only Switching to radio modePRE mode static Digital Directional Antenna mode DDA staticSwitching the RDS function on/off Selecting the radio modeSwitching REG on/off Convenient RDS functions AF, REGSelecting the waveband/memory bank To switch between the FM memory banks FM1, FM2, FM3 and FMTBand is displayed Selecting a wavebandSetting the sensitivity of station seek tuning Tuning into a stationAutomatic station seek tuning Tuning into stations manuallyScanning receivable stations Scan Setting the scanning timeStoring stations Storing stations automatically TravelstoreProgramme type PTY Listening to stored stationsActivating PTY Deactivating PTYTreble reduction feature during interference HiCut Selecting a programme type and starting seek tuningAdjusting HiCut Optimising radio receptionSwitching TIM on/off Switching TIM offTIM Trafﬁc Information Memory Recording trafﬁc announcements Switching TIM onSelecting the TIM message Playing stored trafﬁc announcementsSelecting timers Setting the timerSetting the volume for trafﬁc announcements Switching trafﬁc information priority on/offTrafﬁc information Ejecting a CD CD modeSelecting tracks Starting CD mode, inserting a CDRandom track play MIX Fast searching audibleRepeating tracks Repeat Scanning tracks ScanAdjusting the scrolling text MP3 modeTrafﬁc announcements in CD mode Switching CD scrolling text on/offD01 D02 Inserting/removing MMCs/SDsActivating the MP3 mode of CD Switching to MMC/SD modeOperation during the MP3 mode Inserting an MMC/SDTrack from it Press the Next button 4to redisplay the MP3 main menuMP3 main menu Selecting a track with the joystickCancelling Scan and continuing listening to a track Conﬁguring the displayRepeating individual tracks or whole directories Repeat Adjusting the scrolling text Press the softkey 5 with the display label Show ALLNext tracks are scanned in ascending order CD changer mode optional Switching to CD-changer modeSelecting CDs Repeating individual tracks or whole CDs Repeat Naming CDsRepeat CD brieﬂy appears on the dis- play To stop the current track or current CD from being repeatedCD name is deleted Deleting a CD nameDeleting all CD names CD names are deletedSetting the time automatically Setting the timeSetting the clock manually Setting the dateSwitching DSA on/off DSA Max Digital Sound AdjustmentSwitching DSA off Permanent time displayAutomatically calibrating the equalizer Switching DSA onTo reactivate the equalizer EQ 1 For the driver aloneManually changing the graphical equalizer Viewing vehicle acoustics with/ without equalizerSelecting a sound presetting Preset Resetting the equalizerAfter the calibration or the manual adjust- ment Presettings for the following music styles are availableSelecting a sound effect Adjusting the stage effectSelecting the stage effect Changing the virtual distance of the loudspeakersSwitching DNC off Calibrating DNCStarting the DNC calibration Subwoofer and centre speaker Adjusting the subwoofer increaseSelecting a DNC increase To select a DNC increaseAdjusting the subwoofer phase position Setting the low-pass ﬁlterSetting the subsonic ﬁlter Adjusting high-pass ﬁlters for front/rear Adjusting the centre speakerTMC for dynamic navigation systems Crossover101 Ampliﬁer/Sub-Out Switching the internal ampliﬁer on/offExternal audio sources 102Be selected using the Source button Switching the AUX input on/offNaming the AUX input Press the softkey 5 with the display label AUX1Entering a switch-on message Resetting the deviceMiscellaneous Displaying the serial numberSpeciﬁcations 319 Gerätepass