Blaupunkt MP76 Volume, Setting the power-on volume, Risk of injury, Mute, Telephone audio

Page 9

Volume

Volume

You can adjust the volume in steps from 0 (off) to 50 (maximum).

To increase the volume,

turn the volume control 2clockwise. To decrease the volume,

turn the volume control 2 counter- clockwise.

Setting the power-on volume

You can set the default volume level at which the device plays when it is switched on.

Press the MENU button 9.

Press the softkey 5 with the display label "VOLUME".

Press the softkey 5 with the display label "ON VOL".

Adjust the desired volume with volume control 2.

Press the OK joystick 8or the MENU button 9to exit the menu.

The settings are saved.

Note:

The volume played last before switch- off can also be selected as the power- on volume. For this purpose, press the softkey with the display label "LAST VOL" in the Volume menu

Risk of injury!

If the power-on volume is set to maximum, the volume level can be very high when the device is switched on!

	If the volume was set to maximum be-		ENGLISH
	fore the device was switched off and the

	power-on volume is set to "LAST VOL",
	the volume level can be very high when
	the device is switched on again!
	Severe damage to your hearing can be
	caused in both cases!

Mute

You can decrease the volume abruptly. Brieﬂy press button 1.

The display shows "MUTE".

Cancelling mute

Brieﬂy press button 1again

or

turn the volume control 2.

Telephone audio

If your car sound system is connected withacellphone,"picking"upthephoneauto- maticallymutesthecarsoundsystemandthe call is layed back via the loudspeakers of the card sound system. For this pur- pose, the cell phone must be connec- ted to the device as described in the instal- lation instructions.

61

Image 9

Contents Bremen MP76 Page Slot for MMC/SD Volume CD modeDisplay Adjusting high-pass ﬁlters for Front/rear MP3 modeRepeating individual tracks or TMC for dynamic navigation SystemsSafety note Road safetyInstallation Disposal of old unitTheft protection Activating/deactivating demo modeDetachable control panel Detaching the control panelSwitching on/off using button Switching on/offSwitching on/off using the vehicle ignition Attaching the control panelSetting the power-on volume VolumeRisk of injury MuteActivating the navigation audio Navigation audioAdjusting the bass Sound and volume relationshipAdjusting the treble Adjusting the navigation minimum volumeAdjusting the front/rear volume ratio fader Setting the left/right volume ratio balanceTo adjust the balance, press the Audio button To adjust the fader, press the Audio buttonSetting the button illumination colour Adjusting the viewing angleAdjusting the display brightness DisplaySetting the display illumination colour Selecting a preset colourMixing a colour for the display illumination Inverting display contents Radio mode Adjusting the tunerSetting the number of antennas Selecting static/dynamic radio mode FM only Switching to radio modePRE mode static Digital Directional Antenna mode DDA staticSwitching the RDS function on/off Selecting the radio modeSwitching REG on/off Convenient RDS functions AF, REGSelecting the waveband/memory bank To switch between the FM memory banks FM1, FM2, FM3 and FMTBand is displayed Selecting a wavebandSetting the sensitivity of station seek tuning Tuning into a stationAutomatic station seek tuning Tuning into stations manuallyScanning receivable stations Scan Setting the scanning timeStoring stations Storing stations automatically TravelstoreProgramme type PTY Listening to stored stationsActivating PTY Deactivating PTYTreble reduction feature during interference HiCut Selecting a programme type and starting seek tuningAdjusting HiCut Optimising radio receptionSwitching TIM on/off Switching TIM offTIM Trafﬁc Information Memory Recording trafﬁc announcements Switching TIM onSelecting the TIM message Playing stored trafﬁc announcementsSelecting timers Setting the timerSetting the volume for trafﬁc announcements Switching trafﬁc information priority on/offTrafﬁc information Ejecting a CD CD modeSelecting tracks Starting CD mode, inserting a CDRandom track play MIX Fast searching audibleRepeating tracks Repeat Scanning tracks ScanAdjusting the scrolling text MP3 modeTrafﬁc announcements in CD mode Switching CD scrolling text on/offD01 D02 Inserting/removing MMCs/SDsActivating the MP3 mode of CD Switching to MMC/SD modeOperation during the MP3 mode Inserting an MMC/SDTrack from it Press the Next button 4to redisplay the MP3 main menuMP3 main menu Selecting a track with the joystickCancelling Scan and continuing listening to a track Conﬁguring the displayRepeating individual tracks or whole directories Repeat Adjusting the scrolling text Press the softkey 5 with the display label Show ALLNext tracks are scanned in ascending order CD changer mode optional Switching to CD-changer modeSelecting CDs Repeating individual tracks or whole CDs Repeat Naming CDsRepeat CD brieﬂy appears on the dis- play To stop the current track or current CD from being repeatedCD name is deleted Deleting a CD nameDeleting all CD names CD names are deletedSetting the time automatically Setting the timeSetting the clock manually Setting the dateSwitching DSA on/off DSA Max Digital Sound AdjustmentSwitching DSA off Permanent time displayAutomatically calibrating the equalizer Switching DSA onTo reactivate the equalizer EQ 1 For the driver aloneManually changing the graphical equalizer Viewing vehicle acoustics with/ without equalizerSelecting a sound presetting Preset Resetting the equalizerAfter the calibration or the manual adjust- ment Presettings for the following music styles are availableSelecting a sound effect Adjusting the stage effectSelecting the stage effect Changing the virtual distance of the loudspeakersSwitching DNC off Calibrating DNCStarting the DNC calibration Subwoofer and centre speaker Adjusting the subwoofer increaseSelecting a DNC increase To select a DNC increaseAdjusting the subwoofer phase position Setting the low-pass ﬁlterSetting the subsonic ﬁlter Adjusting high-pass ﬁlters for front/rear Adjusting the centre speakerTMC for dynamic navigation systems Crossover101 Ampliﬁer/Sub-Out Switching the internal ampliﬁer on/offExternal audio sources 102Be selected using the Source button Switching the AUX input on/offNaming the AUX input Press the softkey 5 with the display label AUX1Entering a switch-on message Resetting the deviceMiscellaneous Displaying the serial numberSpeciﬁcations 319 Gerätepass