Lucent Technologies Transtalk 9000 manual Additional Parts, Rubber Feet

Page 11

Additional Parts

The following parts may be necessary, depending upon your installation.

This Kit of Parts is required only when a single (stand-alone) MDW 9030P Pocketphone is installed:

Rubber Feet (4)

Radio Module 11-foot (3.4 m)	Philips Head	Wall Mounting
Power Cord/AC Adapter	Wood Screws (2)	Plate

These additional parts are required when two or more MDW 9030P Pocketphones are installed in the same zone:

4

TRANSTALK

	CAUTION
		ONLY
	USECABLE
AT&T
P⁄	N847667896
		IN
		OUT
OUT		OFSYNC

1

2

3

4

5

6

Carrier

Philips Head

Wood Screws (4)

Expansion Cable 6-foot (1.8 m) for multiple-carrier installation

Carrier Assembly 25-foot (7.6 m)

Power Cord and Standard AC Adapter

For information about ordering parts, see "Ordering Replacement & Optional Parts" in Chapter 4.

Introduction 1-5

Image 11

Contents TransTalk Digital Wireless System Trademarks Contents Using the MDW 9030P Pocketphone Iii Maintaining the MDW 9030P PocketphonePage Introduction What Is a Wireless Phone?About TransTalk 9000 Products TransTalk 9000 System2Introduction Single Carrier InstallationPrivacy Information Where Can You Use Your Pocketphone?About the MDW 9030P Pocketphone 4Introduction Parts ListRubber Feet Additional Parts6Introduction Spare Battery and HeadsetInstalling the MDW 9030P Pocketphone Important Safety InstructionsCardiac Pacemakers 2Installing the MDW 9030P PocketphoneGuidelines for Safe and Efficient Operation Exposure to Radio Frequency EnergyBasic Safety Precautions for Installation and Use 4Installing the MDW 9030P Pocketphone Additional Safety Instructions for Installation PersonnelAC Outlet Check Radio Modules and Carriers 6Installing the MDW 9030P PocketphonePass Key Components8Installing the MDW 9030P Pocketphone General Positioning Rules Positioning a Radio Module or CarriersAdditional Rules for Installing a Single Radio Module Only 10Installing the MDW 9030P PocketphoneWireless Test Mode Display Number Signal Strength Is 12Installing the MDW 9030P PocketphoneInstalling a Single Radio Module 14Installing the MDW 9030P Pocketphone Setting the Power Level Desired Range Approximate 16Installing the MDW 9030P PocketphoneSetting the Control/Expansion DIP Switch 18Installing the MDW 9030P Pocketphone Installing a Single Carrier on a Shelf or DeskMusic OUT 20Installing the MDW 9030P PocketphoneInstalling a Single Carrier on a Wall 22Installing the MDW 9030P Pocketphone Book 24Installing the MDW 9030P Pocketphone Installing Multiple CarriersCarrier, doing so causes all handsets to work 26Installing the MDW 9030P Pocketphone Music If the carriers are plugged into Then 28Installing the MDW 9030P PocketphoneInstallation Self-Test Handset Inserting and Removing Handset’s Battery Pack30Installing the MDW 9030P Pocketphone MAPM2 Changing the Communications System SettingFilling Out the Handset Label 32Installing the MDW 9030P PocketphoneInstalling the Battery Charger Battery ChargerPositioning the Battery Charger 34Installing the MDW 9030P Pocketphone Removing a Battery Pack From the Spare Battery Compartment Inserting a Battery Pack into the Spare Battery CompartmentRemoving the Handset from the Handset Cradle Inserting the Handset into Battery Chargers Handset Cradle36Installing the MDW 9030P Pocketphone Using the MDW 9030P Pocketphone Using the MDW 9030P PocketphoneHandset Controls 2Using the MDW 9030P PocketphoneColumn and Select Buttons Handset Display 4Using the MDW 9030P PocketphoneDisplay Messages Line Status Indicators6Using the MDW 9030P Pocketphone Range IndicatorsLow Battery Indicator Carrying Your Pocketphone Volume ControlAntenna Changing the Handset SettingsChanging the Communications System Button Mapping Setting 8Using the MDW 9030P PocketphoneEnabling or Disabling Line Preselection Enabling or Disabling the Vibrator10Using the MDW 9030P Pocketphone Enabling or Disabling the Alerter Test Modes Using Local Test Mode12Using the MDW 9030P Pocketphone Using Wireless Test Mode Performance/Range Test in Wireless Test Mode 14Using the MDW 9030P PocketphoneAnswering a Call Waking Up the PhoneMaking a Call Preselecting a Line 16Using the MDW 9030P PocketphoneManually Selecting a Line or Programmed Button Answering Calls with a Headset Using a HeadsetUsing the Headset On/Off Button Placing Calls with a Headset 18Using the MDW 9030P PocketphoneBattery Charger Features Battery Charger20Using the MDW 9030P Pocketphone Extending Battery Life 22Using the MDW 9030P Pocketphone Maintaining the MDW 9030P Pocketphone Maintaining the MDW 9030P Pocketphone2Maintaining the MDW 9030P Pocketphone Swapping Extensions 4Maintaining the MDW 9030P Pocketphone ReplacingtheAntennaOrdering Replacement & Optional Parts Troubleshooting ProceduresInstallationProblems Power and Pass 2TroubleshootingPower and Pass LEDs on 4Troubleshooting Handset ProblemsHandset Problems 6Troubleshooting Battery ProblemsFor a multiple-carrier installation Voice Quality Problems8Troubleshooting PARTNER, Part 10Troubleshooting Range ProblemsRange Problems Placed on Hold 12TroubleshootingHandset LED on Battery Charger Problems14Troubleshooting Battery Charger Problems 16Troubleshooting MDW 9030P Pocketphone Compatibility MDW9030PPocketphoneCompatibility2MDW 9030P Pocketphone Compatibility Partner Systems Button Mapping for Partner Systems Communications System Compatibility4MDW 9030P Pocketphone Compatibility Setting the Line-Ringing OptionsMerlin Systems Recall Drop 6MDW 9030P Pocketphone CompatibilityDrop Button Mapping for Merlin 410 and Merlin 820 Systems8MDW 9030P Pocketphone Compatibility Setting the Line Ringing OptionsDefinity G1 R1V4 System 25, System 75, System Definity SystemsDrop 10MDW 9030P Pocketphone CompatibilityScroll Display 12MDW 9030P Pocketphone Compatibility Warranty and Repair Information A-1 Lucent Technologies Limited Warranty Limitation of LiabilityLimitation of Liability In-Warranty Repairs2Warranty and Repair Information Repair InformationWarranty and Repair Information A-3 Post-WarrantyRepairsRegulatory Information B-1 FCC Part 15 RulesIC RSS-210 Compliance Hearing Aid CompatibilitySpecifications C-1 SpecificationsPower 2SpecificationsIndex IN-1 IndexIN-2 Index No Link Index IN-3IN-4 Index Battery Charger Wall-Mounting Template Lucent Technologies Comcode Issue March