Motorola i860 manual 68P80400P73-A

Page 58

BASIC LEVEL TEST MODES AND PROCEDURES: Test Mode Test Procedures

e.Summary selection contains time and longitude/latitude expressed in degrees. Accuracy in meters is also displayed.

f.GPS Version contains information about the custom Sirf software used in the unit.

13.Press Back to return to the Trace Mode display.

14.Scroll down to highlight IMEI/SIM ID, and then press OK to view the IMEI/SIM ID display. The IMEI is the global name assigned to the mobile station at manufacturing time and should correspond to the serial-number tag of the unit. The SIM ID is the SIM electronic serial number and should correspond with the number stamped on the SIM card.

15.Press Back to return to the Trace Mode display.

16.Scroll down to highlight Registr Log, and then press OK to view the Registr Log display. This screen displays the Dispatch Log, Interconnect Log, Packet Data Log, Mobile IP Log, and Phone Rst Log. Registration Log information is updated when the user deselects and selects the Registr Log choice.

17.Press Back to return to the Trace Mode display.

18.Scroll down to highlight Err/Chan Codes, and then press On to view the Err/Chan Codes display. This screen displays the physical channel that the unit is connected to or the radio link procedure that is currently active. Also, displays error codes of errors encountered during normal operation if Err/Chan codes is On. (At power up, Err/Chan Codes is Off)

19.Press Back to return to the Trace Mode display.

20.Scroll down to highlight Current Freq, and then press OK to view the Current Freq display, which shows the current frequency and band.

21.Press Back to return to the Trace Mode display.

22.Scroll down to highlight Dispatch IDs, and then press OK to view the Dispatch IDs display. This screen displays the dispatch group id affiliated with the unit in the current dispatch- location area. Also, displays the dispatch individual id affiliated with the unit in the current dispatch location.

23.Press Back to return to the Trace Mode display.

24.Scroll down to highlight Band Info, and then press OK to view the Band Info display. This screen displays the primary and secondary control channels: Pri Band: 02 for 800 MHz; Sec Band: 02 for 800 MHz and 04 for 900 MHz.

25.Press Back to return to the Trace Mode display.

26.Scroll down to highlight Bandmap, and then press OK to view the Bandmap display. This screen displays the currently selected regional bandmap.

27.Press Back to return to the Trace Mode display.

68P80400P73-A

6-7

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Page I860 Manual Revisions Safety and General Information Electro Magnetic Interference Compatibility Medical DevicesAccessory Safety Information Cleaning and Drying ConsiderationsSafety and General Information Model Information Model Numbering SystemModel Specifications General Receiver TransmitterContents Chapter Chapter Field Level Test Modes Procedures Appendix a Ordering Replacement Parts Who Should Use This Manual PrefaceHow This Manual Is Organized Conventions Used in This Manual Related PublicationsOverview DEN Digital Modulation TechnologySpectrum of i DEN Quad 16QAM DEN Voice Compression Technology RF Transmission BurstsCalling Area Coverage SIM Cards Global Positioning System GPS SectionRemoving and Inserting a SIM Card To remove a SIM card Figure To insert a SIM card FigureCOMPONENTS, ICONS, and Indicators Component ViewsDisplay Icons Main Menu IconsAbc d efg d Opqr s Status IconsDEF Call IconsContacts Type Icons Outbox IconsThis page intentionally left blank Power-Up Sequence DISPLAYS, MESSAGES, and AlertsSelf-Test Reset Errors Power-Down SequenceSelf-Test Errors MessagesService Messages Service MessagesMessage Cause Action Alert Tones Tone Low High Freq Cadence When Tone OccursAlert Tones Alert Tones Mode Cadence Using the Optional Vibrate FunctionVibrator Settings To set unit to vibrate for all callsFrom the main menu, select Settings 2-Way Radio Alert Type This page intentionally left blank Test Equipment Preparing for Basic Level TestingReference Accessories Reference UnitThis page intentionally left blank Customer Care Reset ConditionBasic Level Checks and Self Tests Test ConditionsBasic-Level Test Checklist Basic-Level Test ChecklistPreventive Maintenance To clean the unit approximately 3 minutesShock and pressure test time is approximately 3 minutes Mechanical and Electrical ChecksSIM Card Swap Test SIM card swap test time is approximately 5 minutesLockup Test Accessory Swap TestAccessory swap test time is approximately 5 minutes Lockup test time is approximately 6 minutesBattery connections test time is approximately 5 minutes Battery Connections TestTesting the GPS Receiver To test this functionCamera Test Voltage Recognition TestVoltage recognition test time is approximately 4 minutes Passcode Test TroubleshootingSelf-Test Procedures Passcode test time is approximately 5 minutesSettings check test time is approximately 10 minutes Programming Menu Settings CheckPhone Calls Features Way Radio Options Volume Features PersonalizeSecurity Features From the main menu, select Settings Security SIM PINAdvanced Features From the main menu, select Settings Advanced Headset/SpkerCall Performance Test Call performance test time is approximately 7 minutesThis page intentionally left blank To enter debug mode Basic Level Test Modes and ProceduresEntering Debug Mode Test ModesDisplay Screens Display ScreensName Description Entering Test Mode To enter test modeAudio Loopback Test Test Mode Test ProceduresTo perform the audio loopback test test time approx min To perform the matching test test time approx min ESN and Imei Matching TestEngineering Debug Check To monitor the data in the unitSoftware choice 68P80400P73-A Technician Test Procedures Programming the i 860 UnitConnecting the Unit to the RSS Workstation Data Cable Programming SetupCodeplug Troubleshooting Codeplug Repair ProcedureTo access the codeplug Help topic in Windows Preparing for Field Level Testing Preparing Equipment for TestingUsing RSS Connecting an i DEN Unit to the R-2660To connect the unit to the R-2660 Coaxial Cable In/Out TypeRF Zone Fields and Values To enter Initial Registration modeOperating the R-2660 Field ValueDisassembling and Reassembling the Unit SIM Card Battery CoverInstall RemoveAntenna Required Tools T-4 Torx bitBack Housing Coin Cell Required Tools Black stickMain Board, Microphone Seal, and Keypad Flip Assembly Remove Flip AssemblyPage Install Page Exploded View and Parts List Component List Component Parts ListDescription Part Number Reference Exploded View This page intentionally left blank Field Level Test Modes and Procedures Field-Level Test Checklist Required Test EquipmentField-Level Test Checklist Done Technical Tests Pass FailSee the Strong Signal Environment section Registration/Call TestSQE Reference Chart SQE TestTX Power Test See Entering Test Mode Press Menu, EditBER Test FailPower-Up Test Keypad Test Audio Test Use this test to check the audio portion of the unitReset Test No reset ResetReset Log Test To perform the reset log testModel Assembly MA Test Mode Test Model Assembly MA Test Mode Test GPS Receiver Use this test on a unit to check functionality of the GPSCamera Test Replacement Parts Ordering Replacement Parts and KitsCustomer Service Domestic OrdersTable A-2. i 860 Replacement Kits Replacement KitsDescription Kit Number Vehicle Power Adapters Table A-3. Recommended Test Equipment and Tools Recommended Test Equipment and ToolsDescription Part Number Table A-5. Recommended Software Recommended Programming EquipmentTable A-4. Recommended Programming Equipment Name Part Number DescriptionThis page intentionally left blank Index BcchQAM RSS Vselp @6880400P73@
Top Page Image Contents