Motorola i860 manual Camera Test

Page 95

FIELD LEVEL TEST MODES AND PROCEDURES: Camera Test

8.15Camera Test

Use this test to check camera module. Symptoms: Bad view finder (noise, poor color, synchronization error).

Power up

the unit.

Enter the

Model Assembly

(MA) Test Mode.

	Verify				Fail	Replace
	that the viewfinder					Replace
	that the viewfinder					the camera module
	shows the captured					the camera module
	shows the captured					and repeat the
	image correctly.					and repeat the
	image correctly.					test.
						test.

	Pass					Pass
	Pass

Unit passed test. Look for system, coverage, accessory, or software problems.

Fail

Replace

the main FPC Fail

and repeat the test.

Pass

Replace the main board.

8-16	68P80400P73-A

Image 95

Contents Page I860 Manual Revisions Safety and General Information Medical Devices Electro Magnetic Interference CompatibilityCleaning and Drying Considerations Accessory Safety InformationSafety and General Information Model Numbering System Model InformationGeneral Receiver Transmitter Model SpecificationsContents Chapter Chapter Field Level Test Modes Procedures Appendix a Ordering Replacement Parts How This Manual Is Organized PrefaceWho Should Use This Manual Related Publications Conventions Used in This ManualDEN Digital Modulation Technology OverviewSpectrum of i DEN Quad 16QAM RF Transmission Bursts DEN Voice Compression TechnologyCalling Area Coverage Removing and Inserting a SIM Card Global Positioning System GPS SectionSIM Cards To insert a SIM card Figure To remove a SIM card FigureComponent Views COMPONENTS, ICONS, and IndicatorsMain Menu Icons Display IconsStatus Icons Abc d efg d Opqr sCall Icons DEFOutbox Icons Contacts Type IconsThis page intentionally left blank DISPLAYS, MESSAGES, and Alerts Power-Up SequenceMessages Power-Down SequenceSelf-Test Errors Self-Test Reset ErrorsMessage Cause Action Service MessagesService Messages Alert Tones Tone Low High Freq Cadence When Tone OccursAlert Tones Alert Tones To set unit to vibrate for all calls Using the Optional Vibrate FunctionVibrator Settings Mode CadenceFrom the main menu, select Settings 2-Way Radio Alert Type This page intentionally left blank Reference Unit Preparing for Basic Level TestingReference Accessories Test EquipmentThis page intentionally left blank Test Conditions Reset ConditionBasic Level Checks and Self Tests Customer CareTo clean the unit approximately 3 minutes Basic-Level Test ChecklistPreventive Maintenance Basic-Level Test ChecklistSIM card swap test time is approximately 5 minutes Mechanical and Electrical ChecksSIM Card Swap Test Shock and pressure test time is approximately 3 minutesLockup test time is approximately 6 minutes Accessory Swap TestAccessory swap test time is approximately 5 minutes Lockup TestTo test this function Battery Connections TestTesting the GPS Receiver Battery connections test time is approximately 5 minutesVoltage recognition test time is approximately 4 minutes Voltage Recognition TestCamera Test Passcode test time is approximately 5 minutes TroubleshootingSelf-Test Procedures Passcode TestPhone Calls Features Programming Menu Settings CheckSettings check test time is approximately 10 minutes Way Radio Options Personalize Volume FeaturesFrom the main menu, select Settings Security SIM PIN Security FeaturesFrom the main menu, select Settings Advanced Headset/Spker Advanced FeaturesCall performance test time is approximately 7 minutes Call Performance TestThis page intentionally left blank Test Modes Basic Level Test Modes and ProceduresEntering Debug Mode To enter debug modeName Description Display ScreensDisplay Screens To enter test mode Entering Test ModeTo perform the audio loopback test test time approx min Test Mode Test ProceduresAudio Loopback Test To monitor the data in the unit ESN and Imei Matching TestEngineering Debug Check To perform the matching test test time approx minSoftware choice 68P80400P73-A Programming the i 860 Unit Technician Test ProceduresData Cable Programming Setup Connecting the Unit to the RSS WorkstationTo access the codeplug Help topic in Windows Codeplug Repair ProcedureCodeplug Troubleshooting Preparing Equipment for Testing Preparing for Field Level TestingConnecting an i DEN Unit to the R-2660 Using RSSCoaxial Cable In/Out Type To connect the unit to the R-2660Field Value To enter Initial Registration modeOperating the R-2660 RF Zone Fields and ValuesDisassembling and Reassembling the Unit Remove Battery CoverInstall SIM CardRequired Tools T-4 Torx bit AntennaBack Housing Required Tools Black stick Coin CellMain Board, Microphone Seal, and Keypad Remove Flip Assembly Flip AssemblyPage Install Page Exploded View and Parts List Description Part Number Reference Component Parts ListComponent List Exploded View This page intentionally left blank Field Level Test Modes and Procedures Required Test Equipment Field-Level Test ChecklistDone Technical Tests Pass Fail Field-Level Test ChecklistRegistration/Call Test See the Strong Signal Environment sectionSQE Test SQE Reference ChartSee Entering Test Mode Press Menu, Edit TX Power TestFail BER TestPower-Up Test Keypad Test Use this test to check the audio portion of the unit Audio TestNo reset Reset Reset TestTo perform the reset log test Reset Log TestModel Assembly MA Test Mode Test Model Assembly MA Test Mode Test Use this test on a unit to check functionality of the GPS GPS ReceiverCamera Test Domestic Orders Ordering Replacement Parts and KitsCustomer Service Replacement PartsDescription Kit Number Replacement KitsTable A-2. i 860 Replacement Kits Vehicle Power Adapters Description Part Number Recommended Test Equipment and ToolsTable A-3. Recommended Test Equipment and Tools Name Part Number Description Recommended Programming EquipmentTable A-4. Recommended Programming Equipment Table A-5. Recommended SoftwareThis page intentionally left blank Bcch IndexQAM RSS Vselp @6880400P73@