Motorola i860 manual Using RSS, Connecting an i DEN Unit to the R-2660

Page 63

PREPARING FOR FIELD LEVEL TESTING: Using RSS

Wear a conductive wrist strap in series with a 100 kΩ resistor to ground.

Do not wear nylon clothing when handling any printed-circuit board.

Prior to touching any printed-circuit board, touch an electrical ground to remove any static charge that might have accumulated.

Refer to Service and Repair Note SRN-F1052 for more information. This note is available through:

Motorola Literature Distribution Center

2290 Hammond Drive

Schaumburg, IL 60173 847-576-2826

The following should be considered when storing or transporting a circuit board:

Place the printed-circuit board in conductive, anti-static material.

Do not insert the printed-circuit board into conventional plastic “snow” trays used for transporting other devices.

7.2Using RSS

Use Radio Service Software (RSS) to program a new software version or to update user information in the codeplug. Refer to “Connecting the Unit to the RSS Workstation” and the Radio Service Software User’s Guide for information on the setup and use of RSS.

NOTE: You can use the RSS online Help for locating specific information about RSS dialog boxes and fields. To access online Help, press F1 while you are viewing an RSS screen.

If you are using the R-2660A Communications System Analyzer in the iDEN mode, which is 6:1 capable, use RSS to program an i860 unit for Full Rate operation. Use the 6:1 Interconnect softkey for all interconnect testing.

If you are using the R-2660B or later, which is 3:1 capable, use RSS to program an i860 unit for Half Rate operation. Use the 3:1 Interconnect softkey for all interconnect testing.

In the carrier version of RSS (but not the agent version), you can change interleave values. To access the fields where you can change these interleave values, go to the User Ergonomics dialog box, and then click on the Interleave tab.

NOTE: After servicing a unit, use RSS to reprogram the unit back to its original operating state.

Refer to the R-2660 Digital Communications System Analyzer Operator’s Manual for more information on how to set up this equipment for iDEN mode testing.

7.3Connecting an i DEN Unit to the R-2660

The R-2660 Communications System Analyzer enables you to monitor and perform tests on iDEN units. Figure 7-1 shows a typical R-2660 test setup.

Equipment Required: R-2660, reference SIM card, SMA to N-type RF coaxial cable, battery eliminator, 5.0-12.0 Vdc power supply.

7-2

68P80400P73-A

Image 63
Contents Page I860 Manual Revisions Safety and General Information Medical Devices Electro Magnetic Interference CompatibilityCleaning and Drying Considerations Accessory Safety InformationSafety and General Information Model Numbering System Model InformationGeneral Receiver Transmitter Model SpecificationsContents Chapter Chapter Field Level Test Modes Procedures Appendix a Ordering Replacement Parts Preface Who Should Use This ManualHow This Manual Is Organized Related Publications Conventions Used in This ManualDEN Digital Modulation Technology OverviewSpectrum of i DEN Quad 16QAM RF Transmission Bursts DEN Voice Compression TechnologyCalling Area Coverage Global Positioning System GPS Section SIM CardsRemoving and Inserting a SIM Card To insert a SIM card Figure To remove a SIM card FigureComponent Views COMPONENTS, ICONS, and IndicatorsMain Menu Icons Display IconsStatus Icons Abc d efg d Opqr sCall Icons DEFOutbox Icons Contacts Type IconsThis page intentionally left blank DISPLAYS, MESSAGES, and Alerts Power-Up SequenceMessages Power-Down SequenceSelf-Test Errors Self-Test Reset ErrorsService Messages Service MessagesMessage Cause Action Tone Low High Freq Cadence When Tone Occurs Alert TonesAlert Tones Alert Tones To set unit to vibrate for all calls Using the Optional Vibrate FunctionVibrator Settings Mode CadenceFrom the main menu, select Settings 2-Way Radio Alert Type This page intentionally left blank Reference Unit Preparing for Basic Level TestingReference Accessories Test EquipmentThis page intentionally left blank Test Conditions Reset ConditionBasic Level Checks and Self Tests Customer CareTo clean the unit approximately 3 minutes Basic-Level Test ChecklistPreventive Maintenance Basic-Level Test ChecklistSIM card swap test time is approximately 5 minutes Mechanical and Electrical ChecksSIM Card Swap Test Shock and pressure test time is approximately 3 minutesLockup test time is approximately 6 minutes Accessory Swap TestAccessory swap test time is approximately 5 minutes Lockup TestTo test this function Battery Connections TestTesting the GPS Receiver Battery connections test time is approximately 5 minutesVoltage Recognition Test Camera TestVoltage recognition test time is approximately 4 minutes Passcode test time is approximately 5 minutes TroubleshootingSelf-Test Procedures Passcode TestProgramming Menu Settings Check Settings check test time is approximately 10 minutesPhone Calls Features Way Radio Options Personalize Volume FeaturesFrom the main menu, select Settings Security SIM PIN Security FeaturesFrom the main menu, select Settings Advanced Headset/Spker Advanced FeaturesCall performance test time is approximately 7 minutes Call Performance TestThis page intentionally left blank Test Modes Basic Level Test Modes and ProceduresEntering Debug Mode To enter debug modeDisplay Screens Display ScreensName Description To enter test mode Entering Test ModeTest Mode Test Procedures Audio Loopback TestTo perform the audio loopback test test time approx min To monitor the data in the unit ESN and Imei Matching TestEngineering Debug Check To perform the matching test test time approx minSoftware choice 68P80400P73-A Programming the i 860 Unit Technician Test ProceduresData Cable Programming Setup Connecting the Unit to the RSS WorkstationCodeplug Repair Procedure Codeplug TroubleshootingTo access the codeplug Help topic in Windows Preparing Equipment for Testing Preparing for Field Level TestingConnecting an i DEN Unit to the R-2660 Using RSSCoaxial Cable In/Out Type To connect the unit to the R-2660Field Value To enter Initial Registration modeOperating the R-2660 RF Zone Fields and ValuesDisassembling and Reassembling the Unit Remove Battery CoverInstall SIM CardRequired Tools T-4 Torx bit AntennaBack Housing Required Tools Black stick Coin CellMain Board, Microphone Seal, and Keypad Remove Flip Assembly Flip AssemblyPage Install Page Exploded View and Parts List Component Parts List Component ListDescription Part Number Reference Exploded View This page intentionally left blank Field Level Test Modes and Procedures Required Test Equipment Field-Level Test ChecklistDone Technical Tests Pass Fail Field-Level Test ChecklistRegistration/Call Test See the Strong Signal Environment sectionSQE Test SQE Reference ChartSee Entering Test Mode Press Menu, Edit TX Power TestFail BER TestPower-Up Test Keypad Test Use this test to check the audio portion of the unit Audio TestNo reset Reset Reset TestTo perform the reset log test Reset Log TestModel Assembly MA Test Mode Test Model Assembly MA Test Mode Test Use this test on a unit to check functionality of the GPS GPS ReceiverCamera Test Domestic Orders Ordering Replacement Parts and KitsCustomer Service Replacement PartsReplacement Kits Table A-2. i 860 Replacement KitsDescription Kit Number Vehicle Power Adapters Recommended Test Equipment and Tools Table A-3. Recommended Test Equipment and ToolsDescription Part Number Name Part Number Description Recommended Programming EquipmentTable A-4. Recommended Programming Equipment Table A-5. Recommended SoftwareThis page intentionally left blank Bcch IndexQAM RSS Vselp @6880400P73@