Motorola i860 manual Electro Magnetic Interference Compatibility, Medical Devices

Page 5

SAFETY AND GENERAL INFORMATION

ALL MODELS WITH FCC ID AZ489FT5833 MEET THE GOVERNMENT'S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES.

Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.

The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg.* Tests for SAR are conducted using standard operating positions specified by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.

Before a phone model is available for sale to the public, it must be tested and certified to the FCC that is does not exceed the limit established by the government-adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model phone when tested for use at the ear is 0.96 W/kg and when tested on the body, as described in the user guide, is 1.46 W/kg during packet data transmission. (Body-worn measurements differ among phone models, depending upon available accessories and FCC requirements.) While there may be differences between the SAR levels or various phones and at various positions, they all meet the government requirement for safe exposure.

The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID AZ489FT5833.

Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Association (CTIA) web-site at http://www.wow-com.com.

*In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements.

Electro Magnetic Interference/

Compatibility

NOTE: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility.

Facilities

To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio product in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy.

Aircraft

When instructed to do so, turn off your radio product when on board an aircraft. Any use of a radio product must be in accordance with applicable regulations per airline crew instructions.

Medical Devices

Pacemakers

The Advanced Medical Technology Association (AdvaMed) recommends that a minimum separation of 6 inches (15 cm) be maintained between a handheld wireless radio product and a pacemaker. These recommendations are consistent with those of the U.S. Food and Drug Administration.

Persons with pacemakers should:

ALWAYS keep the radio product more than 6 inches

(15 cm) from their pacemaker when the radio product is turned ON.

Not carry the radio product in a breast pocket.

Use the ear opposite the pacemaker to minimize the potential for interference.

Turn the radio product OFF immediately if you have any reason to suspect that interference is taking place.

Hearing Aids

Some digital wireless radio products may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.

Other Medical Devices

If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information.

Use While Driving

Check the laws and regulations on the use of radio products in the area where you drive. Always obey them. When using the radio product while driving, please:

Give full attention to driving and to the road.

Use hands-free operation, if available.

Pull off the road and park before making or answering a call if driving conditions so require.

iv

68P80400P73-A

Image 5
Contents Page I860 Manual Revisions Safety and General Information Medical Devices Electro Magnetic Interference CompatibilityCleaning and Drying Considerations Accessory Safety InformationSafety and General Information Model Numbering System Model InformationGeneral Receiver Transmitter Model SpecificationsContents Chapter Chapter Field Level Test Modes Procedures Appendix a Ordering Replacement Parts How This Manual Is Organized PrefaceWho Should Use This Manual Related Publications Conventions Used in This ManualDEN Digital Modulation Technology OverviewSpectrum of i DEN Quad 16QAM RF Transmission Bursts DEN Voice Compression TechnologyCalling Area Coverage Removing and Inserting a SIM Card Global Positioning System GPS SectionSIM Cards To insert a SIM card Figure To remove a SIM card FigureComponent Views COMPONENTS, ICONS, and IndicatorsMain Menu Icons Display IconsStatus Icons Abc d efg d Opqr sCall Icons DEFOutbox Icons Contacts Type IconsThis page intentionally left blank DISPLAYS, MESSAGES, and Alerts Power-Up SequenceSelf-Test Errors Power-Down SequenceSelf-Test Reset Errors MessagesMessage Cause Action Service MessagesService Messages Alert Tones Tone Low High Freq Cadence When Tone OccursAlert Tones Alert Tones Vibrator Settings Using the Optional Vibrate FunctionMode Cadence To set unit to vibrate for all callsFrom the main menu, select Settings 2-Way Radio Alert Type This page intentionally left blank Reference Accessories Preparing for Basic Level TestingTest Equipment Reference UnitThis page intentionally left blank Basic Level Checks and Self Tests Reset ConditionCustomer Care Test ConditionsPreventive Maintenance Basic-Level Test ChecklistBasic-Level Test Checklist To clean the unit approximately 3 minutesSIM Card Swap Test Mechanical and Electrical ChecksShock and pressure test time is approximately 3 minutes SIM card swap test time is approximately 5 minutesAccessory swap test time is approximately 5 minutes Accessory Swap TestLockup Test Lockup test time is approximately 6 minutesTesting the GPS Receiver Battery Connections TestBattery connections test time is approximately 5 minutes To test this functionVoltage recognition test time is approximately 4 minutes Voltage Recognition TestCamera Test Self-Test Procedures TroubleshootingPasscode Test Passcode test time is approximately 5 minutesPhone Calls Features Programming Menu Settings CheckSettings check test time is approximately 10 minutes Way Radio Options Personalize Volume FeaturesFrom the main menu, select Settings Security SIM PIN Security FeaturesFrom the main menu, select Settings Advanced Headset/Spker Advanced FeaturesCall performance test time is approximately 7 minutes Call Performance TestThis page intentionally left blank Entering Debug Mode Basic Level Test Modes and ProceduresTo enter debug mode Test ModesName Description Display ScreensDisplay Screens To enter test mode Entering Test ModeTo perform the audio loopback test test time approx min Test Mode Test ProceduresAudio Loopback Test Engineering Debug Check ESN and Imei Matching TestTo perform the matching test test time approx min To monitor the data in the unitSoftware choice 68P80400P73-A Programming the i 860 Unit Technician Test ProceduresData Cable Programming Setup Connecting the Unit to the RSS WorkstationTo access the codeplug Help topic in Windows Codeplug Repair ProcedureCodeplug Troubleshooting Preparing Equipment for Testing Preparing for Field Level TestingConnecting an i DEN Unit to the R-2660 Using RSSCoaxial Cable In/Out Type To connect the unit to the R-2660Operating the R-2660 To enter Initial Registration modeRF Zone Fields and Values Field ValueDisassembling and Reassembling the Unit Install Battery CoverSIM Card RemoveRequired Tools T-4 Torx bit AntennaBack Housing Required Tools Black stick Coin CellMain Board, Microphone Seal, and Keypad Remove Flip Assembly Flip AssemblyPage Install Page Exploded View and Parts List Description Part Number Reference Component Parts ListComponent List Exploded View This page intentionally left blank Field Level Test Modes and Procedures Required Test Equipment Field-Level Test ChecklistDone Technical Tests Pass Fail Field-Level Test ChecklistRegistration/Call Test See the Strong Signal Environment sectionSQE Test SQE Reference ChartSee Entering Test Mode Press Menu, Edit TX Power TestFail BER TestPower-Up Test Keypad Test Use this test to check the audio portion of the unit Audio TestNo reset Reset Reset TestTo perform the reset log test Reset Log TestModel Assembly MA Test Mode Test Model Assembly MA Test Mode Test Use this test on a unit to check functionality of the GPS GPS ReceiverCamera Test Customer Service Ordering Replacement Parts and KitsReplacement Parts Domestic OrdersDescription Kit Number Replacement KitsTable A-2. i 860 Replacement Kits Vehicle Power Adapters Description Part Number Recommended Test Equipment and ToolsTable A-3. Recommended Test Equipment and Tools Table A-4. Recommended Programming Equipment Recommended Programming EquipmentTable A-5. Recommended Software Name Part Number DescriptionThis page intentionally left blank Bcch IndexQAM RSS Vselp @6880400P73@