Motorola i860 manual Safety and General Information

Page 7

SAFETY AND GENERAL INFORMATION

Use of a non-recommended attachment to a battery charger may result in a risk of fire, electric shock, or injury to persons.

Make sure the battery charger power cord is located so that it will not be stepped on, tripped over, or subjected to damage or stress.

An extension cord should not be used with any battery charger unless absolutely necessary. Use of an improper extension cord could result in a risk of fire and electric shock. If an extension cord must be used, make sure that:

The pins on the plug of the extension cord are the same number, size, and shape as those on the plug of the charger.

The extension cord is properly wired and in good electrical condition.

The cord size is 18AWG for lengths up to 100 feet and 16AWG for lengths up to 150 feet.

Do not operate any battery charger if it has received a sharp blow, has been dropped, or has been damaged in any way; take it to a qualified service technician.

Do not disassemble a battery charger; take it to a qualified service technician when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

Maximum ambient temperature around the power supply or transformer of any battery charger should not exceed 40°C (104°F).

The output power from the power supply or transformer must not exceed the rating given on the Desktop Dual- Pocket Charger.

The disconnection from the line voltage is made by unplugging the power supply from the AC receptacle.

To reduce risk of electric shock, unplug any battery charger from the outlet before attempting any maintenance or cleaning.

For optimum charging performance, turn off the radio product while charging it in any battery charger.

vi

68P80400P73-A

Image 7
Contents Page I860 Manual Revisions Safety and General Information Medical Devices Electro Magnetic Interference CompatibilityCleaning and Drying Considerations Accessory Safety InformationSafety and General Information Model Numbering System Model InformationGeneral Receiver Transmitter Model SpecificationsContents Chapter Chapter Field Level Test Modes Procedures Appendix a Ordering Replacement Parts Who Should Use This Manual PrefaceHow This Manual Is Organized Related Publications Conventions Used in This ManualDEN Digital Modulation Technology OverviewSpectrum of i DEN Quad 16QAM RF Transmission Bursts DEN Voice Compression TechnologyCalling Area Coverage SIM Cards Global Positioning System GPS SectionRemoving and Inserting a SIM Card To insert a SIM card Figure To remove a SIM card FigureComponent Views COMPONENTS, ICONS, and IndicatorsMain Menu Icons Display IconsStatus Icons Abc d efg d Opqr sCall Icons DEFOutbox Icons Contacts Type IconsThis page intentionally left blank DISPLAYS, MESSAGES, and Alerts Power-Up SequenceMessages Power-Down SequenceSelf-Test Errors Self-Test Reset ErrorsService Messages Service MessagesMessage Cause Action Alert Tones Tone Low High Freq Cadence When Tone OccursAlert Tones Alert Tones To set unit to vibrate for all calls Using the Optional Vibrate FunctionVibrator Settings Mode CadenceFrom the main menu, select Settings 2-Way Radio Alert Type This page intentionally left blank Reference Unit Preparing for Basic Level TestingReference Accessories Test EquipmentThis page intentionally left blank Test Conditions Reset ConditionBasic Level Checks and Self Tests Customer CareTo clean the unit approximately 3 minutes Basic-Level Test ChecklistPreventive Maintenance Basic-Level Test ChecklistSIM card swap test time is approximately 5 minutes Mechanical and Electrical ChecksSIM Card Swap Test Shock and pressure test time is approximately 3 minutesLockup test time is approximately 6 minutes Accessory Swap TestAccessory swap test time is approximately 5 minutes Lockup TestTo test this function Battery Connections TestTesting the GPS Receiver Battery connections test time is approximately 5 minutesCamera Test Voltage Recognition TestVoltage recognition test time is approximately 4 minutes Passcode test time is approximately 5 minutes TroubleshootingSelf-Test Procedures Passcode TestSettings check test time is approximately 10 minutes Programming Menu Settings CheckPhone Calls Features Way Radio Options Personalize Volume FeaturesFrom the main menu, select Settings Security SIM PIN Security FeaturesFrom the main menu, select Settings Advanced Headset/Spker Advanced FeaturesCall performance test time is approximately 7 minutes Call Performance TestThis page intentionally left blank Test Modes Basic Level Test Modes and ProceduresEntering Debug Mode To enter debug modeDisplay Screens Display ScreensName Description To enter test mode Entering Test ModeAudio Loopback Test Test Mode Test ProceduresTo perform the audio loopback test test time approx min To monitor the data in the unit ESN and Imei Matching TestEngineering Debug Check To perform the matching test test time approx minSoftware choice 68P80400P73-A Programming the i 860 Unit Technician Test ProceduresData Cable Programming Setup Connecting the Unit to the RSS WorkstationCodeplug Troubleshooting Codeplug Repair ProcedureTo access the codeplug Help topic in Windows Preparing Equipment for Testing Preparing for Field Level TestingConnecting an i DEN Unit to the R-2660 Using RSSCoaxial Cable In/Out Type To connect the unit to the R-2660Field Value To enter Initial Registration modeOperating the R-2660 RF Zone Fields and ValuesDisassembling and Reassembling the Unit Remove Battery CoverInstall SIM CardRequired Tools T-4 Torx bit AntennaBack Housing Required Tools Black stick Coin CellMain Board, Microphone Seal, and Keypad Remove Flip Assembly Flip AssemblyPage Install Page Exploded View and Parts List Component List Component Parts ListDescription Part Number Reference Exploded View This page intentionally left blank Field Level Test Modes and Procedures Required Test Equipment Field-Level Test ChecklistDone Technical Tests Pass Fail Field-Level Test ChecklistRegistration/Call Test See the Strong Signal Environment sectionSQE Test SQE Reference ChartSee Entering Test Mode Press Menu, Edit TX Power TestFail BER TestPower-Up Test Keypad Test Use this test to check the audio portion of the unit Audio TestNo reset Reset Reset TestTo perform the reset log test Reset Log TestModel Assembly MA Test Mode Test Model Assembly MA Test Mode Test Use this test on a unit to check functionality of the GPS GPS ReceiverCamera Test Domestic Orders Ordering Replacement Parts and KitsCustomer Service Replacement PartsTable A-2. i 860 Replacement Kits Replacement KitsDescription Kit Number Vehicle Power Adapters Table A-3. Recommended Test Equipment and Tools Recommended Test Equipment and ToolsDescription Part Number Name Part Number Description Recommended Programming EquipmentTable A-4. Recommended Programming Equipment Table A-5. Recommended SoftwareThis page intentionally left blank Bcch IndexQAM RSS Vselp @6880400P73@