NordicTrack NTL01909.2 manual Attach the Left Upright Sleeve not shown to

Page 10

7. Slide the Right Upright Sleeve (96) up against

7

 

 

the console assembly. Attach the Right Upright

 

 

Sleeve with two #8 x 3/4" Tek Screws (29).

 

 

 

Attach the Left Upright Sleeve (not shown) to

 

 

Console

the console assembly in the same way.

 

 

Assembly

 

 

96

29

 

 

29

 

8. Orient the Storage Latch (100) so that the large

8

 

 

barrel and the Latch Knob (118) are in the posi-

 

 

tions shown.

 

 

 

Remove the tie from the upper end of the

 

 

 

Storage Latch (100). Attach the upper end of the

48

 

Storage Latch to the bracket on the Frame (48)

 

with a 3/8" x 1 3/4" Bolt (117) and a 3/8" Nut

 

 

 

(38).

38

117

 

Remove the tie from the lower end of the

 

Storage Latch (100). Keep the holes in the

 

100

 

Latch Cap (119) aligned with the holes in the

 

 

Storage Latch. Make sure to keep the Latch

118

Large

 

Cap inside the Storage Latch. Attach the

Barrel

 

Storage Latch to the bracket on the Base (83)

 

 

 

with a 3/8" x 2" Bolt (113) and a 3/8" Nut (38).

 

 

 

Note: It may be necessary to move the Frame

 

 

 

back and forth to align the Storage Latch with

 

 

 

the bracket.

83

 

 

Lower the Frame (48) (see HOW TO LOWER

38 119 113

 

THE TREADMILL FOR USE on page 30).

 

 

10

Image 10
Contents QUESTIONS? Model No. NTL01909.2 Serial NoTable of Contents Important Precautions Page Power Lines Ground Standoff Service Clamp Before YOU Begin Assembly Star Washers 90. Do not tighten the Bolts Ful not to pinch the Upright Wire HarnessTighten the Bolts yet Are pinched Power is Turned ON. Remove the wireTors are not Connected Properly Console MAY be Damaged When Tighten the six BoltsStorage Latch. Make sure to keep the Latch Console assembly in the same wayAttach the Left Upright Sleeve not shown to Cap inside the Storage Latch. AttachPage Using a Catv Cable HOW to Connect AN AntennaHOW to Connect AN External Source Using the AUDIO/VIDEO Wire HarnessCare and Maintenance HOW to USE the Chest Pulse SensorHOW to PUT on the Chest Pulse Sensor TroubleshootingHOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeFollow your progress with the displays. The matrix-When you Turn on the fan if desiredSelect an event training workout HOW to USE AN Event Training WorkoutStart the walking belt Select a preset workout HOW to USE a Preset WorkoutEnter your weight HOW to Create a Custom Workout HOW to USE a Custom Workout HOW to USE AN Ifit Card Insert an iFit card and select a workoutStart the walking belt Select a television source Adjust the volumeScan for television channels Select the desired channelHOW to Operate the Remote Control HOW to Replace the Batteries in the Remote ControlHOW to Adjust the Television Settings Scan and save channels Exit the MenuHOW to USE the Stereo Sound System Information ModeHOW to Adjust the Cushioning System HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Important The treadmill is not TroubleshootingProblem The power turns off during use Compatible with GFCI-equipped outletsProblem Solution ProblemProblem The chest pulse sensor does not function properly Problem Television reception is poorProblem The volume cannot be turned up Problem The remote control does not function correctlyProblem The television is not receiving a signal Problem The television needs to be cleanedWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Part LIST-Model No. NTL01909.2 Qty DescriptionQty Description R0310A Exploded Drawing B-Model No. NTL01909.2 Exploded Drawing C-Model No. NTL01909.2 Exploded Drawing D-Model No. NTL01909.2 Exploded Drawing E-Model No. NTL01909.2 Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT