NordicTrack NTL01909.2 manual Solution Problem

Page 32
Idler Roller Bolts
b 3–4 in.

PROBLEM:

Next, locate the Reed Switch (20) and the Magnet

(12) on the left side of the Pulley (11). Turn the Pulley until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If neces- sary, loosen the indicated #8 x 3/4" Tek Screw (29), move the Reed Switch slightly, and then retighten the Tek Screw. Reattach the Hood (not shown) with the six #8 x 3/4" Screws (not shown). Run the treadmill for a few minutes to check for a correct speed reading.

The walking belt slows when walked on

Top

 

View

1/8 in.

29

20

11

12

SOLUTION:

PROBLEM:

SOLUTION:

a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 14. b. If the walking belt is overtightened, treadmill perfor-

mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 3 to 4 in. (7 to 10 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few min- utes. Repeat until the walking belt is properly tight- ened.

c.If the walking belt still slows when walked on, please see the front cover of this manual.

The walking belt is off-center or slips when walked on

a. If the walking belt is off-center, remove the key and

 

 

 

UNPLUG THE POWER CORD. If the walking belt

 

a

 

has shifted to the left, use the hex key to turn the

 

 

 

 

 

 

left idler roller bolt clockwise 1/2 of a turn; if the walk-

 

 

 

ing belt has shifted to the right, turn the left idler

 

 

 

roller bolt counterclockwise 1/2 of a turn. Be careful

 

 

 

not to overtighten the walking belt. Plug in the power

 

 

 

cord, insert the key, and run the treadmill for a few

 

 

 

minutes. Repeat until the walking belt is centered.

 

 

 

b. If the walking belt slips when walked on, first remove

 

 

 

 

b

the key and UNPLUG THE POWER CORD. Using

 

the hex key, turn both idler roller bolts clockwise, 1/4

 

 

 

of a turn. When the walking belt is correctly tightened,

 

 

 

you should be able to lift each edge of the walking

 

 

 

belt 3 to 4 in. (7 to 10 cm) off the walking platform. Be

 

 

 

careful to keep the walking belt centered. Then, plug

 

 

 

in the power cord, insert the key, and carefully walk

 

 

 

on the treadmill for a few minutes. Repeat until the

 

 

 

walking belt is properly tightened.

 

 

 

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents QUESTIONS? Model No. NTL01909.2 Serial NoTable of Contents Important Precautions Page Power Lines Ground Standoff Service Clamp Before YOU Begin Assembly Tighten the Bolts yet Ful not to pinch the Upright Wire HarnessStar Washers 90. Do not tighten the Bolts Power is Turned ON. Remove the wire Tors are not Connected Properly Console MAY be Damaged WhenAre pinched Tighten the six BoltsConsole assembly in the same way Attach the Left Upright Sleeve not shown toStorage Latch. Make sure to keep the Latch Cap inside the Storage Latch. AttachPage HOW to Connect AN Antenna HOW to Connect AN External SourceUsing a Catv Cable Using the AUDIO/VIDEO Wire HarnessHOW to USE the Chest Pulse Sensor HOW to PUT on the Chest Pulse SensorCare and Maintenance TroubleshootingPRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModeFollow your progress with the displays. The matrix-When you Turn on the fan if desiredStart the walking belt HOW to USE AN Event Training WorkoutSelect an event training workout Enter your weight HOW to USE a Preset WorkoutSelect a preset workout HOW to Create a Custom Workout HOW to USE a Custom Workout HOW to USE AN Ifit Card Insert an iFit card and select a workoutStart the walking belt Adjust the volume Scan for television channelsSelect a television source Select the desired channelHOW to Operate the Remote Control HOW to Replace the Batteries in the Remote ControlHOW to Adjust the Television Settings Scan and save channels Exit the MenuHOW to Adjust the Cushioning System Information ModeHOW to USE the Stereo Sound System HOW to Fold and Move the Treadmill HOW to Move the TreadmillHOW to Lower the Treadmill for USE Troubleshooting Problem The power turns off during useImportant The treadmill is not Compatible with GFCI-equipped outletsProblem Solution ProblemProblem The chest pulse sensor does not function properly Problem Television reception is poorProblem The remote control does not function correctly Problem The television is not receiving a signalProblem The volume cannot be turned up Problem The television needs to be cleanedExercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencySuggested Stretches Part LIST-Model No. NTL01909.2 Qty DescriptionQty Description R0310A Exploded Drawing B-Model No. NTL01909.2 Exploded Drawing C-Model No. NTL01909.2 Exploded Drawing D-Model No. NTL01909.2 Exploded Drawing E-Model No. NTL01909.2 Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents