NordicTrack NTL01909.2 manual Scan and save channels, Exit the Menu

Page 27

6.Scan and save channels.

Select CATV or AIR. Select CATV to receive chan- nels through the 75 ohm terminal on the treadmill. Select AIR to receive channels through an antenna. To scan for available channels, highlight AUTO SCAN or AUTO SCAN ADD CH. To scan all chan- nels, select the Auto scan option. To scan all chan- nels and add an extra channel, select the Auto Scan Add Ch option. The scan channel submenu will appear.

If you are receiving channels through a CATV cable, high-

light CABLE SYS- Cable SystemAUTO

TEM and select the Start to Scan auto, STD, IRC, or

HRC setting. Try all UP/DOWN ADJUST "MENU": EXIT

four cable settings, if necessary, to find the optimal setting.

Highlight START TO SCAN and press the Volume increase button to start the auto scan. The televi- sion will begin scanning all of the channels avail- able in your area. When no signal is detected on a channel, the channel will be skipped. When a sig- nal is detected, the channel will be saved into memory and the next channel will be selected. This process will continue until the highest channel is reached. The television will renumber the channels in the order in which it locates them. Do not re- move the key while the television is scanning channels. Note: If a television channel disappears, scan for channels again.

After all valid chan-

 

 

 

 

nels available in your

 

 

 

 

area have been

No.

Program Name

Skip

saved into the televi-

4-1

FD 3803

 

Off

9-2

KQUED-SD

Off

sionʼs memory, you

 

 

 

 

can manually skip

 

 

 

 

unwanted channels.

"ENTER": SELECT

"MENU": EXIT

To skip a channel,

 

 

 

 

highlight CHANNEL

 

 

 

 

SKIP and press the Volume increase button on

your remote control. In the channel skip submenu,

press the Channel increase and decrease buttons

to highlight the desired channel and the Volume in-

crease and decrease buttons to turn on or turn off

the skip option. Continue this process until you

have skipped all unwanted channels.

 

 

To change the dis-

 

 

 

 

play name of a chan-

 

 

 

 

nel, highlight CHAN-

 

 

 

 

NEL NO. and select

 

 

 

 

a channel. Then,

F D

3

8

0 3

highlight CHANNEL

 

 

 

 

LABEL and press the

EDIT

SELECT

"MENU": EXIT

Volume increase but-

 

4 5 6

 

ton to enter the

 

 

 

 

channel label submenu. Press the Volume in- crease and decrease buttons to select a number or letter box. Then press the Channel increase and decrease buttons to select the desired number or letter.

7.Exit the Menu.

When you have finished adjusting the settings, press the Exit button.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Model No. NTL01909.2 Serial No QUESTIONS?Table of Contents Important Precautions Page Power Lines Ground Standoff Service Clamp Before YOU Begin Assembly Ful not to pinch the Upright Wire Harness Star Washers 90. Do not tighten the BoltsTighten the Bolts yet Tighten the six Bolts Power is Turned ON. Remove the wireTors are not Connected Properly Console MAY be Damaged When Are pinchedCap inside the Storage Latch. Attach Console assembly in the same wayAttach the Left Upright Sleeve not shown to Storage Latch. Make sure to keep the LatchPage Using the AUDIO/VIDEO Wire Harness HOW to Connect AN AntennaHOW to Connect AN External Source Using a Catv CableTroubleshooting HOW to USE the Chest Pulse SensorHOW to PUT on the Chest Pulse Sensor Care and MaintenanceOperation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Follow your progress with the displays. The matrix-When youHOW to USE AN Event Training Workout Select an event training workoutStart the walking belt HOW to USE a Preset Workout Select a preset workoutEnter your weight HOW to Create a Custom Workout HOW to USE a Custom Workout Insert an iFit card and select a workout HOW to USE AN Ifit CardStart the walking belt Select the desired channel Adjust the volumeScan for television channels Select a television sourceHOW to Replace the Batteries in the Remote Control HOW to Operate the Remote ControlHOW to Adjust the Television Settings Exit the Menu Scan and save channelsInformation Mode HOW to USE the Stereo Sound SystemHOW to Adjust the Cushioning System HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Compatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Important The treadmill is notSolution Problem ProblemProblem Television reception is poor Problem The chest pulse sensor does not function properlyProblem The television needs to be cleaned Problem The remote control does not function correctlyProblem The television is not receiving a signal Problem The volume cannot be turned upExercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesSuggested Stretches Qty Description Part LIST-Model No. NTL01909.2Qty Description R0310A Exploded Drawing B-Model No. NTL01909.2 Exploded Drawing C-Model No. NTL01909.2 Exploded Drawing D-Model No. NTL01909.2 Exploded Drawing E-Model No. NTL01909.2 Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents