NordicTrack NTL01909.2 manual Follow your progress with the displays. The matrix-When you

Page 17
Contacts

5.Follow your progress with the displays. The matrix—When you

select the manual mode, the matrix will display a track that rep- resents 1/4 mile (400 meters). As you exer- cise, the indicators

around the track will appear in succession until the entire track appears. The track will then disappear and the indicators will again begin to appear in succession.

The Time display— The Time display will show the elapsed time. Note: When a workout is selected, the display will show the time re-

maining in the workout instead of the elapsed time.

The Distance/Incline display—The Distance/Incline display can show the distance that you have walked or run. The display will

also show the incline of the treadmill for several seconds each time the incline changes.

The Calories/Pulse display—The Calories/Pulse display can show the approxi- mate number of calories you have burned. The

display will also show your heart rate when you use the handgrip pulse sensor or the chest pulse sensor.

The Speed display— The Speed display will show the speed of the walking belt.

To reset the console, press the Stop button, re- move the key, and then reinsert the key.

6.Measure your heart rate if desired.

Note: If you use the handgrip pulse sensor and the chest pulse sensor at the same time, the

console will not display your heart rate accu- rately. See page 13 for information about the chest pulse sensor.

Before using the handgrip pulse sensor, remove the sheets of clear plastic from the metal contacts. In addition, make sure that your hands are clean.

To measure your heart rate, stand on the foot rails and hold the metal contacts on the handrail for approximately ten seconds—avoid moving your hands. When your pulse is detected, several dashes will appear in the display and then your heart rate will be shown. For the most accurate heart rate reading, continue to hold the con- tacts for about 15 seconds.

7.Turn on the fan if desired.

The fan features high and low speed settings. Press the Fan button repeatedly to select a fan speed or to turn off the fan. Note: If the fan is on when the walking belt is stopped, the fan will turn off automatically after a few minutes.

8.When you are finished exercising, remove the key from the console.

Step onto the foot rails, press the Stop button, and adjust the incline of the treadmill to the lowest setting. The incline must be at the lowest set- ting when you fold the treadmill to the storage position, or you may damage the treadmill. Next, remove the key from the console and put it in a secure place.

When you are finished using the treadmill, switch the reset/off circuit breaker to the off position and unplug the power cord. IMPORTANT: If you do not do this, the treadmillʼs electrical compo- nents may wear prematurely.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Model No. NTL01909.2 Serial No QUESTIONS?Table of Contents Important Precautions Page Power Lines Ground Standoff Service Clamp Before YOU Begin Assembly Tighten the Bolts yet Ful not to pinch the Upright Wire HarnessStar Washers 90. Do not tighten the Bolts Tors are not Connected Properly Console MAY be Damaged When Power is Turned ON. Remove the wireAre pinched Tighten the six BoltsAttach the Left Upright Sleeve not shown to Console assembly in the same wayStorage Latch. Make sure to keep the Latch Cap inside the Storage Latch. AttachPage HOW to Connect AN External Source HOW to Connect AN AntennaUsing a Catv Cable Using the AUDIO/VIDEO Wire HarnessHOW to PUT on the Chest Pulse Sensor HOW to USE the Chest Pulse SensorCare and Maintenance TroubleshootingPRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Follow your progress with the displays. The matrix-When youStart the walking belt HOW to USE AN Event Training WorkoutSelect an event training workout Enter your weight HOW to USE a Preset WorkoutSelect a preset workout HOW to Create a Custom Workout HOW to USE a Custom Workout Insert an iFit card and select a workout HOW to USE AN Ifit CardStart the walking belt Scan for television channels Adjust the volumeSelect a television source Select the desired channelHOW to Replace the Batteries in the Remote Control HOW to Operate the Remote ControlHOW to Adjust the Television Settings Exit the Menu Scan and save channelsHOW to Adjust the Cushioning System Information ModeHOW to USE the Stereo Sound System HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingImportant The treadmill is not Compatible with GFCI-equipped outletsSolution Problem ProblemProblem Television reception is poor Problem The chest pulse sensor does not function properlyProblem The television is not receiving a signal Problem The remote control does not function correctlyProblem The volume cannot be turned up Problem The television needs to be cleanedExercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Qty Description Part LIST-Model No. NTL01909.2Qty Description R0310A Exploded Drawing B-Model No. NTL01909.2 Exploded Drawing C-Model No. NTL01909.2 Exploded Drawing D-Model No. NTL01909.2 Exploded Drawing E-Model No. NTL01909.2 Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents