NordicTrack NTL01909.2 manual HOW to Operate the Remote Control

Page 25

HOW TO OPERATE THE REMOTE CONTROL

The first time you use the re- mote control, insert batteries (see HOW TO REPLACE THE BATTERIES IN THE REMOTE

CONTROL at the right). Next, stand on the treadmill and hold the remote control near the

television. Point the remote con- trol directly at the television.

Press the Power button ( ). After a few moments, the television will turn on or turn off.

Press the Volume (VOL) increase or decrease button to navigate left or right in a menu. For best results, change the volume by pressing the Volume buttons on the console only.

Press the Mute button to turn on or turn off the sound. Press the numbered channel buttons or the Channel (CH) increase or decrease button to select a channel. The Channel increase and decrease buttons on the re- mote also function as the up and down navigation but- tons in a menu.

Press the Return button ( ) to view the previous channel.

To select a subchannel, select a channel, press the Subchannel button ( ), and then press the numbered channel buttons.

Press the Menu button to view the main menu or to view a previous menu. See pages 26 and 27 for infor- mation on the menu.

Press the Exit button to exit any menu.

Press the PRLIST button to view a list of channels. If you have labeled any channels, the menu will also show the channel label. See page 27 for information on labeling channels. Note: You can also view this list by pressing the PR List button on the console.

Press the EPG button to view the electronic program guide. Note: The electronic program guide is only available when viewing ATSC digital television.

Press the Info button to view information about the cur- rent program and the broadcast or cable signal.

Press the CC button repeatedly to turn on or turn off closed captioning. See step 5 on page 26 to adjust closed captioning settings.

Press the TV/AV button repeatedly to select the input source. To view television channels through an an- tenna or a CATV cable, select the TV source. To use the audio/video wire harness, select the AV source. Press the MTS button repeatedly to select mono, stereo, or SAP (secondary audio programming) as the audio setting.

Press the Format button repeatedly to select auto, 4:3, or wide image as the display format. Note: The auto display format is only available when viewing ATSC digital television.

Press the Pict button repeatedly to select standard, dy- namic, soft, or personal as the image mode.

Press the Audio button repeatedly to select standard, music, movie, or personal as the audio mode.

HOW TO REPLACE THE BATTERIES IN THE REMOTE CONTROL

To replace the batteries, first locate the battery cover on the back of the remote control. Push down lightly on the bat- tery cover with your thumb and slide off the battery cover.

If necessary, remove the old batteries from the remote control. Insert two new “AAA” batteries. Make sure to insert the batteries as shown in the drawing. Then, slide the battery cover onto the remote control.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Model No. NTL01909.2 Serial No QUESTIONS?Table of Contents Important Precautions Page Power Lines Ground Standoff Service Clamp Before YOU Begin Assembly Star Washers 90. Do not tighten the Bolts Ful not to pinch the Upright Wire HarnessTighten the Bolts yet Tors are not Connected Properly Console MAY be Damaged When Power is Turned ON. Remove the wireAre pinched Tighten the six BoltsAttach the Left Upright Sleeve not shown to Console assembly in the same wayStorage Latch. Make sure to keep the Latch Cap inside the Storage Latch. AttachPage HOW to Connect AN External Source HOW to Connect AN AntennaUsing a Catv Cable Using the AUDIO/VIDEO Wire HarnessHOW to PUT on the Chest Pulse Sensor HOW to USE the Chest Pulse SensorCare and Maintenance TroubleshootingHOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerTurn on the fan if desired Follow your progress with the displays. The matrix-When youSelect an event training workout HOW to USE AN Event Training WorkoutStart the walking belt Select a preset workout HOW to USE a Preset WorkoutEnter your weight HOW to Create a Custom Workout HOW to USE a Custom Workout Insert an iFit card and select a workout HOW to USE AN Ifit CardStart the walking belt Scan for television channels Adjust the volumeSelect a television source Select the desired channelHOW to Replace the Batteries in the Remote Control HOW to Operate the Remote ControlHOW to Adjust the Television Settings Exit the Menu Scan and save channelsHOW to USE the Stereo Sound System Information ModeHOW to Adjust the Cushioning System HOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Lower the Treadmill for USE Problem The power turns off during use TroubleshootingImportant The treadmill is not Compatible with GFCI-equipped outletsSolution Problem ProblemProblem Television reception is poor Problem The chest pulse sensor does not function properlyProblem The television is not receiving a signal Problem The remote control does not function correctlyProblem The volume cannot be turned up Problem The television needs to be cleanedExercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencySuggested Stretches Qty Description Part LIST-Model No. NTL01909.2Qty Description R0310A Exploded Drawing B-Model No. NTL01909.2 Exploded Drawing C-Model No. NTL01909.2 Exploded Drawing D-Model No. NTL01909.2 Exploded Drawing E-Model No. NTL01909.2 Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents