NordicTrack NTB49030 user manual Cable Tool is routed through the bolts

Page 15

37. Thread the end of the High Cable (54) into the

37

 

 

 

 

Cable Tool (27). Route the Cable Tool and Cable

 

 

 

 

 

 

 

 

74

through the Side Top Frame (7). Make sure that

 

 

 

 

 

 

 

 

45

the Cable Tool is routed through the bolts in

 

 

Between

 

 

 

the Top Frame as indicated; if the High Cable

 

 

Bolts

 

rubs against a bolt, damage may occur.

 

 

7

 

 

Remove the Cable Tool from the Cable.

 

 

 

 

 

 

 

 

 

Hold a 3 1/2” Pulley (45) inside the High Cable

54

 

 

 

 

 

 

 

 

 

(54) as shown. Attach the Pulley inside the brack-

 

 

 

 

62

et on the Center Top Frame (2) with an M10 x

27

 

 

 

 

48mm Button Bolt (74) and an M10 Nylon

 

 

 

 

Locknut (62).

 

 

 

 

 

38. Make sure the High Cable (54) is routed under

38

 

 

 

 

the indicated rods on the Swivel Arm (14).

 

 

 

 

 

62

 

 

 

 

 

 

 

 

Attach a 4” Pulley (89) inside the Swivel Arm (14)

 

65 14

 

 

Rods

 

 

 

 

with an M10 x 54mm Button Bolt (73), two M10

 

 

 

 

 

 

 

 

 

Washers (65), two 7mm Spacers (48), and an

 

 

65

 

 

M10 Nylon Locknut (62). Make sure the High

 

 

 

 

 

 

 

 

 

Cable (54) rests in the groove of the Pulley.

 

48

 

73

 

 

 

 

 

 

 

 

54

89

 

 

 

 

 

 

 

 

 

 

48

 

 

39. Slide a Clip Cover (43) onto the High Cable (54).

39

 

 

 

 

 

 

 

 

 

Hold an M6 Nylon Locknut (63) inside a Clip (42),

 

 

 

 

 

and insert the High Cable (54) into the Clip and

 

 

 

 

 

the Locknut. Insert a screwdriver between the

 

 

54

 

 

Locknut and the Clip. Rotate the screwdriver, the

 

43

 

 

 

Clip, and the Locknut together until two threads of

 

 

 

 

 

 

 

 

 

the Cable show past the Locknut.

 

 

 

 

 

Slide the Clip Cover (43) over the Clip (42).

 

42

63

 

 

 

 

 

 

 

 

 

 

 

40. Route the Cable Tool (27) through the Left

40

 

 

 

 

Stabilizer (92). Make sure that the Cable Tool is

 

 

 

 

 

 

 

 

 

routed around the bolts in the Stabilizer as

 

 

 

 

 

indicated; if the Low Cable (55) rubs against a

 

 

 

 

27

bolt, damage may occur.

 

 

 

 

 

 

 

 

 

Locate the Low Cable (55). Thread the end of

 

42

 

 

55

the Cable without the Clip (42) into the Cable Tool

 

 

 

(27). Make sure the Cable is inside the indicat-

 

89

 

 

ed rod on the Swivel Arm (14). Pull the Cable

 

 

 

 

 

48

 

 

through the Left Stabilizer (92). Remove the

 

 

 

92

Cable from the Cable Tool.

 

 

 

 

 

48

 

 

 

 

 

 

 

 

Attach a 4” Pulley (89) inside the Swivel Arm (14)

73

 

 

 

 

with an M10 x 54mm Button Bolt (73), two M10

 

 

 

 

Washers (65), two 7mm Spacers (48), and an

65

 

 

 

 

 

 

 

 

M10 Nylon Locknut (62). Make sure the Low

Rod

14

65

62

 

Cable rests in the groove of the Pulley.

 

 

 

 

 

 

 

 

 

 

15

 

 

 

 

Image 15
Contents QUESTIONS? Model No. NTB49030 Serial NoCustomer HOT Line Table of Contents Important Precautions Before YOU Begin Right SideLeft Side Make Things Easier for Yourself AssemblyDo not tighten the Locknuts yet Page Do not tighten the Locknuts yet Grease Page Page Page Cated rods on the Swivel Arm Side Top Frame 7. Make sure that the CableTool is routed around the bolts in the Top Make sure the Cable is inside of the indiHigh Cable 54 rests in the groove Pulley Trap is oriented to hold the CableGroove of the Pulley Locknut 62. Make sure the Cable rests Groove of the PulleyCable rests in the groove of the Pulley Cable Tool is routed through the boltsTop Frame as indicated if the High Cable Rubs against a bolt, damage may occurCable is routed under the bolts in the Base Make sure the Cable is routed under the boltsLocknut 62. Make sure the Cable is Groove of the Pulley Cable is routed over the rods on the Swivel ArmCable 55 rests in the groove of the Pulley Page Adjusting the Safety Spotter AdjustmentsAttaching Accessories Adjusting the Weight RestsAttaching a Barbell to the Cables Adding Weights to the Weight Carriage or BarbellCarriage Cable Cable DiagramsHigh Cable Butterfly CableLow Cable Base CableTroubleshooting and Maintenance Tightening the CablesReplace all cables at least every two years Exercise Guidelines Muscle Chart Cooling DownStaying Motivated Thursday Aerobic Exercise Date Exercise Weight Sets RepsDate Aerobic ExerciseMonday Qty Description Part LIST-Model No. NTB49030R0304A Part Identification CHART-Model No. NTB49030Exploded DRAWING-Model No. NTB49030 Limited Warranty Ordering Replacement Parts