Diamondback 1190 Er manual Random Program

Page 25

119OM 8/28/06 11:43 AM Page 27

Workout Programs, continued

RANDOM PROGRAM

Getting Started

The Random program is designed to allow you to choose a random computer-generat- ed profile for your workout.

Beginning the Program

Start pedaling the unit. The message window will scroll a message “SELECT A PRO- GRAM”. Press the Classic Programs key until the RANDOM program LED indicator lights up.

Accepting Default values or Entering the program setting mode

When the message display flashes, “RANDOM”, it indicates you are about to select the Random program. The message display will scroll “PRESS ENTER TO ADJUST OR START TO BEGIN”.

•Press “START” key to accept current default values and begin the Random program workout.

o Default time = 30 minutes

•Or press “ENTER” key to enter program setup mode. The message display will bring you through the program setup step by step as below:

Entering Age

1.If ENTER key is pressed, the message window will flash once, “ENTER YOUR AGE”, then “AGE = XX” will start blinking.

2.Press “UP/DOWN” key to adjust the age.

3.After age is adjusted, then press “ENTER” key to accept.

Entering Weight

1.If ENTER key is pressed, the message window will flash once, “ENTER YOUR WEIGHT”, then “WEIGHT = XX” will start blinking.

2.Press “UP/DOWN” key to adjust the weight.

3.After weight is adjusted, then press “ENTER” key to accept.

Entering Program Time

1.If ENTER key is pressed, the message window will flash once, “ENTER PROGRAM TIME”, then “TIME = 30 MIN” will start blinking.

2.Pressing “UP/DOWN” key to adjust the time. When the time setting reaches 60 minutes, the display will show “TIME = 1HR 00MIN”.

3.After time is adjusted, the message window will display “SET UP COMPLETED” “PRESS START TO BEGIN”. You may press the “START” key to begin this program.

Note: You may press the START key at any time during program setup to skip the adjust- ment and begin your workout. By doing so, the console will use default value of age and weight for %HR and calories burned calculations.

During the Program

Display

•Once the program is started, the message window will display the workout data of “Time, Intensity Level, Watts, and Calories”.

•Press the “SELECT” key to switch the display to “% Max HR, Strides/Min,

 

25

1190 Er Owner’s Manual

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 119OM 8/28/06 1143 AM Purchaser’s Reference Information To Activate WarrantyShipping Materials Table of Contents Introduction Figure a Safety Instructions and WarningsAssembly Drawing Console Mast Assembly Assembly InstructionsHandrail Assembly Handrail & Steparm Covers AssemblyWater bottle & Leveling Pads Console AssemblyAdjusting the Ellipse Angle BodyFit Angle AdjustmentDifference in Ellipse Angle Exercise guidelines BMI = weight lb ÷ height2 in xGood health is an exercise in common sense Heart rate is an important key to your exerciseKeep the % of your maximum heart rate accurate Get a smart start on exercising Pulse Grip Operating Tips Pulse Hand Grips StandardChest Strap Standard Exercise guidelines Intensity Level Definition ConsoleConsole Layout and Controls Heart Rate Bar Graph Pulse IndicatorPulse Display Standard Program KeysData Display Select Key Function KeysBasic Operation Basic Operation R M U P Workout ProgramsR K O U T S U M M a R Y A S S I C P R O G R a M S Pause, Reset, Switch, Stop or Save the program Random Program Program Profile Workout Programs Program Profile Special DOT Matrix Track Display Total Trainer Program Workout Programs I N T E R a C T I V E P R O G R a M S Entering Target Heart Rate Heart Rate Interval Program Entering Rest Lower HR Goal Fatburner Program Cardio Program Workout Programs Workout Programs Demo Mode Maintenance Effective August Domestic warranty InformationDiamondback Fitness, Inc Diamondback Fitness Warranty Card Warranty cardCamarillo Ranch Road Camarillo, CA
Top Page Image Contents