Bushnell 70-0002 Temperature Alarm, Beep Function, Stopwatch Mode, Countdown / Reverse-Timer Mode

Page 5

Temperature Alarm

Sets the alarm to sound when the temperature measurement reaches the programmed level. In the Alarm Mode, the Temperature alarm uses the same measurement units (ºC or F) that were last set in the Temperature Mode. To change this you must first change the temperature units in the Temperature Mode. Using the UP or DOWN buttons once changes the temperature in tenths of a degree. Holding either button down changes the temperature in increments of 1 degree.

Beep Function

In the Alarm mode, a Beep function is also available. When activated, the beep function causes a beep sound to be made whenever a button is depressed, even when the Alarm function is turned off. To activate the function go to the Beep function in the Alarm Mode, press the COMP button and ‘ON’ is displayed. Press again and ‘OFF’ is displayed.

Stopwatch Mode

Press the MODE button until Stop Watch Mode is displayed. To operate, press the UP button to start and press again to stop. Pressing the DOWN button will reset the Stop Watch.

For split timing function, press the DOWN button while the Stop Watch is operating in order to stop the display and press again to continue. You can also press the DOWN button while the Stop Watch is operating to stop the display and then press the UP button to stop the Stop Watch and display the final reading. Press the DOWN button again to reset the Stop Watch.

Stop Watch Mode / Split Timing Function

Split timing function is displayed as ‘SPL’ when activated and the display returns to normal when DOWN button is pressed.

6

COUNTDOWN TIMER ALARM

Countdown / Reverse-Timer Mode

Press the MODE button until Countdown Timer Mode is displayed, represented by ‘RT’ (reverse timer). To operate press the UP button to start and press again to stop, then press the DOWN button to reset the Countdown Timer.

To set the Countdown Timer press and hold down the ADJ button for 3 seconds, which will cause the seconds setting to blink. Adjust with the UP or DOWN button, and then press the MODE button to adjust next setting. Press the ADJ button to save settings and exit. Press the COMP for ‘AUTO’ to allow Countdown Timer to repeat function automatically, and press COMP again to turn off ‘AUTO’ function.

Press any button when alarm sounds to stop the Countdown Timer. If nothing is pressed the Countdown Timer will stop beeping after 10 seconds, but it will continue if the ‘AUTO’ function is set on. To stop the Countdown Timer if the ‘Auto’ function is on, you must go to the Countdown Timer Mode and press COMP to turn off the ‘Auto’ function and then press UP button to stop it.

DIGITAL COMPASS

Compass Mode

Press the MODE button until Time Mode is displayed, and then press the COMP button. If already in Time Mode, simply press the COMP button and Compass Mode is displayed. Hold the compass level using the bubble level to get a reading. If the Cardinal Points blink then the compass probably needs to be calibrated. (See trouble shooting tips.)

Compass Calibration

In Compass Mode, hold down ADJ button for 3 seconds. Calibration Mode is displayed. Put the compass on a level, non- magnetic surface and press the COMP button. The word CAL will start blinking. Then, rotate the compass 2 full circles slowly WHILE HOLDING THE COMPASS LEVEL. When done, press COMP again. When completed, the display shows ‘DONE’ and it will then go automatically into Declination Setting Mode. If Calibration is

7

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Manual de Instruções Manuale di IstruzioniEnglish Français Setting Mode Button CompassAdjustment LCD DisplayDate Settings Default Time Mode / Time SettingsNew Settings Temperature ModeStopwatch Mode Temperature AlarmStop Watch Mode / Split Timing Function Countdown / Reverse-Timer ModeSelf Homing Mode Declination SettingNight Mode Installing a BatteryU.S.A. Send to Canada Send to Trouble ShootingWarranty / Repair Ecran à Cristaux Liquides Bouton de ModeBouton De RéglageNouveaux Réglages New Settings Réglages de date Date SettingsMode Température Temperature Mode Mode Réglage Alarme Alarm Setting ModeMode Chronomètre Stopwatch Mode Alarme Température Temperature AlarmMode Chronomètre/Fonction de chronométrage fractionné Stop Watch Mode/Split Timing ModeMode Autoguidage Self Homing Mode Réglage de Déclinaison Declination SettingMode Nuit Night Mode Installation de la pile Installing a BatteryDurée de Vie des Piles Battery Life Indicateur de Tension Faible de Pile Low Battery IndicatorDépannage Garantie / RéparationPantalla LCD BotónNivel de Brújula QUÉ Significan LOS Botones ADJModalidad de Temperatura Temperature Mode Nuevas Configuraciones New SettingsAlarma Cómo SE Ajusta EL TiempoModalidad de Cronómetro Stopwatch Mode Alarma de Temperatura Temperature AlarmModalidad de Brújula Compass Mode Función de Señal Acústica Beep FunctionModalidad de Indicación del Rumbo Self Homing Mode Configuración de la Declinación Declination SettingModalidad Nocturna Night Mode Cómo se instalan las pilas Installing a BatteryVida útil de la pila Battery Life Indicador de nivel bajo de las pilas Low Battery IndicatorCorrección DE Anormalidades Garantía / ReparaciónKompass-Level Down-Knopf Down LCD-DisplayNeue Einstellungen New Settings Datumseinstellung Date SettingsModus Temperatur Temperature Mode Modus Alarmeinstellung Alarm Setting ModeModus Stoppuhr Stopwatch Mode Temperaturalarm Temperature AlarmModus Countdown/Reverse Timer Countdown/Reverse-Timer Mode Modus Kompass Compass ModeModus Zieleingabe Self Homing Mode Deklinationseinstellung Declination SettingNachtmodus Night Mode Einlegen einer Batterie Installing a BatteryBatteriehaltbarkeit Battery Life Anzeige schwache Batterie Low Battery IndicatorHinweise ZUR Fehlerbeseitigung Garantie / ReparaturTasto Cambio Modalità Pulsante Display a Cristalli LiquidiModalità Bussola TastoImpostazione della Data Modalità Data/Ora predefinita / ImpostazioniNuove Impostazioni Modalità TemperaturaFunzione Bip Allarme TemperaturaModalità Cronometro Modalità Cronometro / Funzione Tempo ParzialeIndicatore di Bassa Carica della Pila Installazione della PilaTaratura della Bussola Impostazione della DeclinazioneGaranzia Limitata PER DUE Anni Durata della PilaTela de LCD Botão de Luz de Ajuste da Fundo ConfiguraçãoBotão de Modo Da BússolaNovas Configurações Modo de Horário Padrão / Configurações do HorárioModo de Configuração do Alarme Ajustes da DataFunção de Bip Alarme de TemperaturaModo de Cronômetro Modo de Cronômetro / Função de Divisão de TempoCalibragem da Bússola Configuração de DeclinaçãoModo de Orientação Automática Modo NoturnoVida Útil da Pilha Indicador de Baixa Carga da PilhaGarantia Limitada DE Dois Anos NOS EUA Remeter Para
Top Page Image Contents