Weider 831.159821 user manual Butterfly Arm, Frame must be able to pivot easily

Page 10

14.

Lubricate an M10 x 80mm Button Head Bolt (97)

14

Lubricate

97

 

 

and both sides of two Plastic Washers (55) with

 

Welded

 

 

 

 

grease. Attach the Right Butterfly Arm (11) to the

 

 

 

 

 

 

Bushing

55

54

 

 

Butterfly Frame (9) with the Bolt, the two Plastic

 

 

 

 

 

 

11

 

 

 

 

Washers, two Butterfly Caps (54), and an M10

 

 

 

 

 

 

 

 

 

 

 

Nylon Locknut (70).

Do not overtighten the

 

55

 

 

 

 

Locknut; the Butterfly Arm must be able to

 

 

 

 

 

 

 

 

 

 

 

pivot easily. Be sure the indented sides of the

 

 

54

 

 

 

Plastic Washers fit over the welded bushing in

 

 

 

 

 

 

Lubricate

 

 

 

 

the Butterfly Arm.

 

 

 

9

10

 

 

 

 

 

 

 

 

 

 

70

 

Repeat this step with the Left Butterfly Arm

 

 

 

 

 

 

 

 

 

 

 

(10).

 

 

 

 

 

 

15. Attach the Bumper (25) to the Right Leg (73) with

15

 

 

 

 

 

an M4 x 20mm Self-tapping Screw (77) and an

 

 

 

 

 

 

 

 

73

 

 

M5 Washer (50).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

23

Lubricate

 

 

 

Press two 40mm x 50mm Inner Caps (23) into

 

 

 

 

 

 

 

 

 

 

 

the ends of the Leg Lever (4).

 

 

 

 

 

 

Lubricate an M10 x 60mm Bolt (63) with grease.

 

70

 

25

 

 

Attach the Leg Lever (4) to the Right Leg (73)

 

 

6377

 

 

with the Bolt and an M10 Nylon Locknut (70).

Do

 

50

 

 

not overtighten the Locknut; the Leg Lever

 

4

 

 

 

 

must be able to pivot easily.

 

 

 

 

 

 

 

 

 

 

23

 

 

 

16.

Press a 50mm x 70mm Inner Cap (22) into the

16

 

 

 

 

 

top of the Leg Press Frame (30).

 

 

 

 

 

 

 

 

 

 

 

Lubricate an M10 x 80mm Bolt (61) with grease.

 

 

 

22

 

 

 

 

 

 

 

 

Attach the Leg Press Frame (30) to the Left Base

 

 

 

 

 

 

(2) with the Bolt and an M10 Nylon Locknut (70).

 

 

 

 

 

 

Do not overtighten the Locknut; the Leg Press

 

 

 

30

 

 

Frame must be able to pivot easily.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

70

 

 

 

 

 

 

61

 

 

 

 

 

 

 

 

Lubricate

 

 

 

 

 

2

 

 

 

 

 

 

10

 

 

 

 

Image 10
Contents Serial Number Decal under seat SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important Precautions Before YOU Begin Using the weight systemLeft Side Assembly requires two people AssemblyFrame Assembly Make Things Easier for YourselfSide shown Do not tighten the M10 Nylon Locknuts 70 yet Nylon LocknutSide is on top LargeDo not tighten the M10 Nylon Locknuts Yet With two M10 x 85mm Bolts 60, two M10Attach the Right Seat Frame 5 to the Right 65mm Bolts 63, four M10 Washers 75, Two M10 Nylon LocknutsShown Not tighten the Locknuts yetButterfly Frame must be able to pivot easily ARM AssemblyRepeat this step with the Left Butterfly Arm Butterfly Arm Frame must be able to pivot easilyAn M10 Nylon Locknut Cable AssemblyLocate the High Cable 45. Route the Cable up Groove of the PulleyIng An M8 Nylon LocknutLocate the Leg Press Cable 95.Attach M8 Nylon Locknut Locate the Butterfly CablePage Locate the Leg Lever Cable Attach a 90mm Pulley 38 inside the Right LegLocknut Ing Locate the Low Cable 47. Route the small ballPulley Wrap the Low Cable 47 around a 90mm Pulley Is turned to hold the Cable in the groove of the Pulley M10 Nylon Locknut 70. Be sure the Cable TrapOn the Upright Seat Assembly Frame 9. Attach the tether on the Pins to Screw 68. Do not fully tighten the ScrewChanging the Weight Setting AdjustmentsAttaching the Accessories to a Pulley Station Converting the Butterfly ArmsPulley move smoothly Adjusting the LEG Press PlateTightening the Cables Move smoothlyWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Weight Resistance ChartLbs Left Top Cable Diagrams Low CableLeg Press Cable Cable ID Chart46 47 3/7 96 95 1/2 95 148 1/4 47 276 3/4 45 116 3/4 Exercise Guidelines Cooling Down Muscle ChartStaying Motivated If parts become worn and need to Full 90 DAY WarrantyModel No SEARS, Roebuck and CO., Hoffman ESTATES, ILCheck to see if it has been pre-assembled Part Identification CHART-Model No Page Save this Part LIST/EXPLODED Drawing for Future Reference Part LIST-Model No Qty Description Key No. QtyDRAWING-Model No R0403A