Weider 831.159821 user manual An M8 Nylon Locknut, Ing, Locate the Leg Press Cable 95.Attach

Page 12

21.Wrap the High Cable (45) around a 90mm Pulley (38). Attach the Pulley at the forward hole, inside of the bracket on the Center Top Frame (14) with

an M10 x 45mm Bolt (66) and an M10 Nylon Locknut (70).

22. Attach the end of the High Cable (45) to the

Small “U”-Bracket (79) with an M8 Washer (26)

and an M8 Nylon Locknut (71).

Note: Do not

completely tighten the Nylon Locknut; it

 

should be threaded only two turns onto the

 

end of the Cable, as shown in the inset draw-

 

ing.

 

Attach the Small “U”-Bracket (79) to the Weight

Tube (82) with an M8 x 45mm Bolt (69) and an

M8 Nylon Locknut (71). Do not overtighten the

Locknut; the Weight Tube should be able to pivot in the “U”-Bracket.

23. Locate the Leg Press Cable (95).Attach the

Cable inside the Left Leg (36) with aM10 x 70mm

Bolt (81), two M10 Washers (75), two Long

Spacers (80), and an M10 Nylon Locknut (70).

24.Wrap the Leg Press Cable (95) around a 90mm Pulley (38). Attach the Pulley inside the Leg Press Frame (30) with an M10 x 70mm Bolt (81), two M10 Washers (75), two 13mm Spacers (34), and an M10 Nylon Locknut (70).

12

21

 

 

70

 

 

 

 

 

 

 

 

 

 

14

 

 

 

 

 

45

 

 

 

 

38

 

 

 

 

 

 

66

 

22

 

 

 

 

 

 

 

45

 

 

 

79

 

71

 

 

 

 

 

 

 

 

 

 

26

 

45

 

69

 

71

 

 

 

 

 

 

 

 

 

 

82

 

 

 

 

 

 

 

 

71

23

 

 

 

 

 

 

 

 

 

75

70

 

81

80

 

 

 

 

 

 

 

 

 

 

 

 

80

 

 

 

 

 

95

 

 

 

75

 

 

 

 

 

36

 

 

 

24

 

 

 

 

 

 

 

 

38

75

 

 

 

 

 

 

 

 

 

 

 

70

 

34

 

 

34

 

 

75

 

95

 

 

 

 

 

30

 

 

81

 

 

 

 

 

Image 12
Contents Serial Number Decal under seat SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important Precautions Using the weight system Before YOU BeginLeft Side Assembly Frame AssemblyAssembly requires two people Make Things Easier for YourselfNylon Locknut Side is on topSide shown Do not tighten the M10 Nylon Locknuts 70 yet LargeWith two M10 x 85mm Bolts 60, two M10 Attach the Right Seat Frame 5 to the RightDo not tighten the M10 Nylon Locknuts Yet 65mm Bolts 63, four M10 Washers 75, Two M10 Nylon LocknutsShown Not tighten the Locknuts yetARM Assembly Butterfly Frame must be able to pivot easilyRepeat this step with the Left Butterfly Arm Butterfly Arm Frame must be able to pivot easilyCable Assembly Locate the High Cable 45. Route the Cable upAn M10 Nylon Locknut Groove of the PulleyAn M8 Nylon Locknut IngLocate the Leg Press Cable 95.Attach M8 Nylon Locknut Locate the Butterfly CablePage Locate the Leg Lever Cable Attach a 90mm Pulley 38 inside the Right LegIng Locate the Low Cable 47. Route the small ball LocknutPulley Wrap the Low Cable 47 around a 90mm Pulley M10 Nylon Locknut 70. Be sure the Cable Trap Is turned to hold the Cable in the groove of the PulleyOn the Upright Seat Assembly Frame 9. Attach the tether on the Pins to Screw 68. Do not fully tighten the ScrewAdjustments Attaching the Accessories to a Pulley StationChanging the Weight Setting Converting the Butterfly ArmsAdjusting the LEG Press Plate Tightening the CablesPulley move smoothly Move smoothlyWeight Resistance Chart Weight High Press LEG Butter LOW Pulley ARM FLY ARM LeverLbs Left Top Cable Diagrams Low CableCable ID Chart Leg Press Cable46 47 3/7 96 95 1/2 95 148 1/4 47 276 3/4 45 116 3/4 Exercise Guidelines Muscle Chart Cooling DownStaying Motivated Full 90 DAY Warranty Model NoIf parts become worn and need to SEARS, Roebuck and CO., Hoffman ESTATES, ILCheck to see if it has been pre-assembled Part Identification CHART-Model No Page Save this Part LIST/EXPLODED Drawing for Future Reference Part LIST-Model No Qty Description Key No. QtyDRAWING-Model No R0403A