Weider 831.159821 user manual Ing Locate the Low Cable 47. Route the small ball, Locknut, Pulley

Page 16

37.Attach the end of the Leg Lever Cable (96) to the other “U”-Bracket (85) with an M8 Washer (26)

and an M8 Nylon Locknut (71).

Note: Do not

completely tighten the Nylon Locknut; it

 

should be threaded only two turns onto the

 

end of the Cable, as shown in the inset draw-

 

ing.

 

38.Locate the Low Cable (47). Route the small ball

on the Cable through the cage on the Leg Press Frame (30).

Attach a 90mm Pulley (38) inside the Leg Press Frame (30) with an M10 x 70mm Bolt (81), two M10 Washers (75), two 13mm Spacers (34), and an M10 Nylon Locknut (70).

39.Route the Low Cable (47) through the Left Leg

(36)and the Left Upright (7). Attach a 90mm Pulley (38) inside the Upright with an M10 x 70mm Bolt (81), two M10 Washers (75), two 13mm Spacers (34), and an M10 Nylon Locknut

40.Wrap the Low Cable (47) around a 90mm Pulley

(38).Attach the Pulley and a Cable Trap (91) to the lower set of holes in the indicated “U”-Bracket

(85)with an M10 x 50mm Bolt (62) and an M10

Nylon

Locknut (70).

Be sure the Cable Trap is

turned

to hold the Cable in the groove of the

Pulley.

 

37

 

 

 

 

96

 

96

 

26

 

 

 

 

 

71

85

71

 

 

38

 

 

 

 

 

30

 

 

38

34

70

 

 

 

 

 

 

75

34

 

Cage

 

 

81

75

 

47

 

 

39

 

 

 

 

 

34

 

38

 

75

 

 

70

 

 

 

 

 

 

47

 

 

 

36

 

34

 

 

 

75

7

 

 

81

 

 

 

 

 

40

 

 

 

 

85

 

 

 

62

70

 

 

 

91

 

 

38

 

 

 

 

47

 

16

Image 16
Contents Serial Number Decal under seat SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important Precautions Before YOU Begin Using the weight systemLeft Side Assembly Frame AssemblyAssembly requires two people Make Things Easier for YourselfNylon Locknut Side is on topSide shown Do not tighten the M10 Nylon Locknuts 70 yet LargeWith two M10 x 85mm Bolts 60, two M10 Attach the Right Seat Frame 5 to the RightDo not tighten the M10 Nylon Locknuts Yet 65mm Bolts 63, four M10 Washers 75, Two M10 Nylon LocknutsShown Not tighten the Locknuts yetButterfly Frame must be able to pivot easily ARM AssemblyRepeat this step with the Left Butterfly Arm Butterfly Arm Frame must be able to pivot easilyCable Assembly Locate the High Cable 45. Route the Cable upAn M10 Nylon Locknut Groove of the PulleyIng An M8 Nylon LocknutLocate the Leg Press Cable 95.Attach M8 Nylon Locknut Locate the Butterfly CablePage Locate the Leg Lever Cable Attach a 90mm Pulley 38 inside the Right LegLocknut Ing Locate the Low Cable 47. Route the small ballPulley Wrap the Low Cable 47 around a 90mm Pulley Is turned to hold the Cable in the groove of the Pulley M10 Nylon Locknut 70. Be sure the Cable TrapOn the Upright Seat Assembly Frame 9. Attach the tether on the Pins to Screw 68. Do not fully tighten the ScrewAdjustments Attaching the Accessories to a Pulley StationChanging the Weight Setting Converting the Butterfly ArmsAdjusting the LEG Press Plate Tightening the CablesPulley move smoothly Move smoothlyWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Weight Resistance ChartLbs Left Top Cable Diagrams Low CableLeg Press Cable Cable ID Chart46 47 3/7 96 95 1/2 95 148 1/4 47 276 3/4 45 116 3/4 Exercise Guidelines Cooling Down Muscle ChartStaying Motivated Full 90 DAY Warranty Model NoIf parts become worn and need to SEARS, Roebuck and CO., Hoffman ESTATES, ILCheck to see if it has been pre-assembled Part Identification CHART-Model No Page Save this Part LIST/EXPLODED Drawing for Future Reference Part LIST-Model No Qty Description Key No. QtyDRAWING-Model No R0403A