Weider 831.159821 user manual Nylon Locknut, Side is on top, Large, Hole

Page 6

3.Attach the Base Plate (37) to the Left Base (2) with an M10 x 135mm Bolt (58) and an M10

Nylon Locknut (70).

Be sure that the texture

side is on top.

 

Attach the Left Upright (7) to the Left Base (2) with the two indicated M10 x 65mm Carriage Bolts (57) and two M10 Nylon Locknuts (70).

Attach the Left Leg (36) to the Left Base (2) with the two indicated M10 x 65mm Carriage Bolts

(57) and two M10 Nylon Locknuts (70).Be sure the large upper hole in the Left Leg is on the

side shown.

Do not tighten the M10 Nylon Locknuts (70) yet.

4.Press a 50mm x 70mm Inner Cap (22) into the top of the Right Leg (73).

Attach the Right Leg (73) to the Right Base (1) with the two M10 x 65mm Carriage Bolts (57) and two M10 Nylon Locknuts (70).

Attach the Right Upright (6) to the Right Base (1) with the two indicated M10 x 65mm Carriage Bolts (57) and two M10 Nylon Locknuts (70).

Do not tighten the M10 Nylon Locknuts (70) yet.

3

 

 

 

7

 

2

70

36

70

 

 

Large

 

 

 

70

Hole

 

 

70

 

57

 

 

 

70

 

57

37

 

 

 

 

58

4

 

 

 

 

6

 

22

 

 

 

70

 

73

70

 

 

 

70

 

 

70

57

 

 

 

 

1

 

57

 

6

Image 6
Contents Serial Number Decal under seat SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important Precautions Using the weight system Before YOU BeginLeft Side Assembly requires two people AssemblyFrame Assembly Make Things Easier for YourselfSide shown Do not tighten the M10 Nylon Locknuts 70 yet Nylon LocknutSide is on top LargeDo not tighten the M10 Nylon Locknuts Yet With two M10 x 85mm Bolts 60, two M10Attach the Right Seat Frame 5 to the Right 65mm Bolts 63, four M10 Washers 75, Two M10 Nylon LocknutsShown Not tighten the Locknuts yetARM Assembly Butterfly Frame must be able to pivot easilyRepeat this step with the Left Butterfly Arm Butterfly Arm Frame must be able to pivot easilyAn M10 Nylon Locknut Cable AssemblyLocate the High Cable 45. Route the Cable up Groove of the PulleyAn M8 Nylon Locknut IngLocate the Leg Press Cable 95.Attach M8 Nylon Locknut Locate the Butterfly CablePage Locate the Leg Lever Cable Attach a 90mm Pulley 38 inside the Right LegIng Locate the Low Cable 47. Route the small ball LocknutPulley Wrap the Low Cable 47 around a 90mm Pulley M10 Nylon Locknut 70. Be sure the Cable Trap Is turned to hold the Cable in the groove of the PulleyOn the Upright Seat Assembly Frame 9. Attach the tether on the Pins to Screw 68. Do not fully tighten the ScrewChanging the Weight Setting AdjustmentsAttaching the Accessories to a Pulley Station Converting the Butterfly ArmsPulley move smoothly Adjusting the LEG Press PlateTightening the Cables Move smoothlyWeight Resistance Chart Weight High Press LEG Butter LOW Pulley ARM FLY ARM LeverLbs Left Top Cable Diagrams Low CableCable ID Chart Leg Press Cable46 47 3/7 96 95 1/2 95 148 1/4 47 276 3/4 45 116 3/4 Exercise Guidelines Muscle Chart Cooling DownStaying Motivated If parts become worn and need to Full 90 DAY WarrantyModel No SEARS, Roebuck and CO., Hoffman ESTATES, ILCheck to see if it has been pre-assembled Part Identification CHART-Model No Page Save this Part LIST/EXPLODED Drawing for Future Reference Part LIST-Model No Qty Description Key No. QtyDRAWING-Model No R0403A