Weider 831.159821 user manual Frame 9. Attach the tether on the Pins to

Page 20

	53. Insert the two Locking Pins (53) into the Butterfly	53
	Frame (9). Attach the tether on the Pins to the	53
	Frame (9). Attach the tether on the Pins to the	53
	Butterfly Frame with an M4 x 9.5mm Self-tapping	53
	Butterfly Frame with an M4 x 9.5mm Self-tapping
	Screw (68). Do not fully tighten the Screw.
		68
		9
		53

54.Make sure that all parts have been properly tightened. The use of all remaining parts will be explained in ADJUSTMENTS, starting on the following page.

Before using the weight system, pull each cable a few times to make sure that the cables move smoothly

over the pulleys. If one of the cables does not move smoothly, find and correct the problem.IMPORTANT: If the cables are not properly routed, they may be damaged when heavy weight is used. See the CABLE

DIAGRAM on pages 24 and 25 of this manual for proper cable routing. If there is any slack in the cables, you will need to remove it by tightening the cables; see TIGHTENING THE CABLES on page 22.

Image 20

Contents Serial Number Decal under seat SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important Precautions Left Side Using the weight systemBefore YOU Begin Assembly Frame AssemblyAssembly requires two people Make Things Easier for YourselfNylon Locknut Side is on topSide shown Do not tighten the M10 Nylon Locknuts 70 yet LargeWith two M10 x 85mm Bolts 60, two M10 Attach the Right Seat Frame 5 to the RightDo not tighten the M10 Nylon Locknuts Yet 65mm Bolts 63, four M10 Washers 75, Two M10 Nylon LocknutsShown Not tighten the Locknuts yetRepeat this step with the Left Butterfly Arm ARM AssemblyButterfly Frame must be able to pivot easily Butterfly Arm Frame must be able to pivot easilyCable Assembly Locate the High Cable 45. Route the Cable upAn M10 Nylon Locknut Groove of the PulleyLocate the Leg Press Cable 95.Attach An M8 Nylon LocknutIng M8 Nylon Locknut Locate the Butterfly CablePage Locate the Leg Lever Cable Attach a 90mm Pulley 38 inside the Right LegPulley Ing Locate the Low Cable 47. Route the small ballLocknut Wrap the Low Cable 47 around a 90mm Pulley On the Upright M10 Nylon Locknut 70. Be sure the Cable TrapIs turned to hold the Cable in the groove of the Pulley Seat Assembly Frame 9. Attach the tether on the Pins to Screw 68. Do not fully tighten the ScrewAdjustments Attaching the Accessories to a Pulley StationChanging the Weight Setting Converting the Butterfly ArmsAdjusting the LEG Press Plate Tightening the CablesPulley move smoothly Move smoothlyLbs Left Top Weight Resistance ChartWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Cable Diagrams Low Cable46 47 3/7 96 95 1/2 95 148 1/4 47 276 3/4 45 116 3/4 Cable ID ChartLeg Press Cable Exercise Guidelines Staying Motivated Muscle ChartCooling Down Full 90 DAY Warranty Model NoIf parts become worn and need to SEARS, Roebuck and CO., Hoffman ESTATES, ILCheck to see if it has been pre-assembled Part Identification CHART-Model No Page Save this Part LIST/EXPLODED Drawing for Future Reference Part LIST-Model No Qty Description Key No. QtyDRAWING-Model No R0403A

Frame (9). Attach the tether on the Pins to the

Screw (68). Do not fully tighten the Screw.