Weider 831.159821 Tightening the Cables, Pulley move smoothly, Move smoothly, See drawing B

Page 22

TIGHTENING THE CABLES

Woven cable, the type of cable used on the weight

system, can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the

cables should be tightened.

See drawing A. Slack can be removed by moving the 90mm Pulley (38) and Cable Trap (91) to a higher set of holes in a Double “U”-Bracket (56). Remove the

M10 Nylon Locknut (70) and the M10 x 50mm Bolt (62) from the Cable Trap, the Pulley, and the Double “U”- Bracket. Re-attach the Pulley and the Cable Trap to

the new set of holes in the Double “U”-Bracket with the

Bolt and Locknut. Make sure that the Cable Trap is in the proper position and that the Cable and

Pulley move smoothly.

Move the 90mm Pulley (38) in the other Double “U”-Bracket (56) in the same manner.

See drawing B. Slack can be removed by moving the 90mm Pulley (38) and the Cable Trap (91) to the high- er set of holes in a “U”-Bracket (85). Remove the M10 Nylon Locknut (70) and the M10 x 50mm Bolt (62) from the Cable Trap, the Pulley, and the “U”-Bracket. Re-attach the Pulley and the Cable Trap to the higher

set of holes in the “U”-Bracket with the Bolt and Locknut. Make sure that the Cable Trap is in the proper position and that the Cable and Pulley

move smoothly.

Move the 90mm Pulley (38) in the other “U”-Bracket (85) in the same manner.

See drawing B.

Slack can also be removed from the

 

cables by tightening the M8 Nylon Locknuts (71)

 

attaching a cable to either “U”-Bracket (85), or the

 

Small “U”-Bracket (79). To do this, you may need to

 

remove the 90mm Pulley (38) from the “U”-Bracket, or

 

remove the Small “U”-Bracket from the Weight Tube

 

(not shown). Make sure that the cables are not too tight

 

or the Top Weight (74) will be lifted off the weight stack.

 

ADJUSTING THE LEG PRESS PLATE

 

To adjust the Leg Press Plate (31), remove the Leg

 

Press Pin (87) from the Leg Press Frame (30) and the

 

Adjustment Tube (88). Move the Tube to the desired

 

position and secure it in place with the Pin.

Be sure

the Pin is turned to the locked position around the

 

Leg Press Frame.

 

 

A

 

 

 

 

 

56

 

91

 

56

 

 

 

 

70

 

62

 

 

 

38

 

B

 

 

 

 

74

 

79

 

 

85

 

 

 

70

 

 

 

 

71

 

 

38

 

 

 

62

 

 

 

 

74

 

 

 

 

79

 

 

 

30

31

 

 

 

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Serial Number Decal under seat SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important Precautions Before YOU Begin Using the weight systemLeft Side Assembly requires two people AssemblyFrame Assembly Make Things Easier for YourselfSide shown Do not tighten the M10 Nylon Locknuts 70 yet Nylon LocknutSide is on top LargeDo not tighten the M10 Nylon Locknuts Yet With two M10 x 85mm Bolts 60, two M10Attach the Right Seat Frame 5 to the Right 65mm Bolts 63, four M10 Washers 75, Two M10 Nylon LocknutsShown Not tighten the Locknuts yetButterfly Frame must be able to pivot easily ARM AssemblyRepeat this step with the Left Butterfly Arm Butterfly Arm Frame must be able to pivot easilyAn M10 Nylon Locknut Cable AssemblyLocate the High Cable 45. Route the Cable up Groove of the PulleyIng An M8 Nylon LocknutLocate the Leg Press Cable 95.Attach M8 Nylon Locknut Locate the Butterfly CablePage Locate the Leg Lever Cable Attach a 90mm Pulley 38 inside the Right LegLocknut Ing Locate the Low Cable 47. Route the small ballPulley Wrap the Low Cable 47 around a 90mm Pulley Is turned to hold the Cable in the groove of the Pulley M10 Nylon Locknut 70. Be sure the Cable TrapOn the Upright Seat Assembly Frame 9. Attach the tether on the Pins to Screw 68. Do not fully tighten the ScrewChanging the Weight Setting AdjustmentsAttaching the Accessories to a Pulley Station Converting the Butterfly ArmsPulley move smoothly Adjusting the LEG Press PlateTightening the Cables Move smoothlyWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Weight Resistance ChartLbs Left Top Cable Diagrams Low CableLeg Press Cable Cable ID Chart46 47 3/7 96 95 1/2 95 148 1/4 47 276 3/4 45 116 3/4 Exercise Guidelines Cooling Down Muscle ChartStaying Motivated If parts become worn and need to Full 90 DAY WarrantyModel No SEARS, Roebuck and CO., Hoffman ESTATES, ILCheck to see if it has been pre-assembled Part Identification CHART-Model No Page Save this Part LIST/EXPLODED Drawing for Future Reference Part LIST-Model No Qty Description Key No. QtyDRAWING-Model No R0403A
Top Page Image Contents