Weider WESY99300 A 3/8 Nylon Locknut, End and a loop on the other, Butterfly Base, Make

Page 12

19. Wrap the Medium Cable (72) over a 4 1/2” Pulley

 

 

 

19

 

 

 

 

(34) in the direction shown. Attach the Pulley to the

 

 

 

 

 

 

 

 

64

 

 

 

Butterfly Top Frame (64) with a 3/8” x 1 3/4” Bolt (22)

 

 

 

 

 

 

and a 3/8” Nylon Locknut (4).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

22

34

4

 

 

 

 

 

 

 

 

72

 

 

 

20. Attach the threaded shaft on the Medium Cable (72)

 

 

 

20

 

 

 

 

to the Small “U”-Bracket (43) with a 1/4” Flat Washer

 

 

 

 

 

 

 

 

 

 

 

 

 

(11) and a 1/4” Nylon Locknut (16).

 

Note: See the

 

 

72

 

 

inset drawing. Do not completely tighten the

 

 

 

 

 

2

 

 

Nylon Locknut; it should be threaded only two

 

 

 

 

 

 

 

turns onto the end of the Cable.

 

 

 

 

 

 

43

 

 

 

 

 

 

 

 

11

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

 

Attach the Small “U”-Bracket (43) to the Weight Tube

 

 

 

 

16

 

 

 

 

 

 

77

72

 

(77) with a 5/16” x 1 3/4” Bolt (9) and a 5/16” Nylon

 

 

 

 

 

 

 

 

 

 

Locknut (2).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11

16

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

43

 

21. Identify the Long Cable (73). It has a ball on one

 

 

21

 

 

 

 

end and a loop on the other.

Route

the end

with

the

 

 

 

 

 

 

 

 

 

loop through the slot in the cable guide on the

 

 

 

 

 

 

 

 

Butterfly Base (61).

 

 

 

 

 

 

 

 

 

Route the Long Cable (73) under a 3 1/2” Pulley (5)

 

 

 

 

 

61

 

as shown. Attach the Pulley and a Cable Trap (39) to

 

 

 

 

4

 

 

the indicated bracket on the Butterfly Base (61) with a

 

 

Cable

 

 

 

 

 

 

 

 

 

3/8” x 2” Bolt (35) and a 3/8” Nylon Locknut (4).

 

Make

 

 

 

 

 

Guide

 

 

5

 

sure the Cable Trap is oriented as shown.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

73

 

39

35

 

 

 

 

 

 

 

 

 

 

 

 

 

12

 

 

 

 

 

Image 12
Contents Model No. WESY99300 Serial No Our factoryTable of Contents Limited WarrantyImportant Precautions Read all instructions in this manualKeep hands and feet away from moving parts New decal in the appropriate locationUsing the weight system Before YOU BeginAssembly Locate and open the parts bag labelled Frame Assembly Head of each BoltDo not tighten Nylon Locknuts yet Attach the Weight Guides 58 to the Butterfly Base Pin Grooves 1717 4LubricateInto the top of the Butterfly Top Frame Flat Washers 19, and two 5/16 Nylon LocknutsTwo 5/16 Nylon Locknuts ClosestTighten all nylon locknuts used in steps 1 through Locate and open the parts bag labelled ARM Bushings should fit onto the ends of the tubePress Base. This will be a tight fit Locknut the Press Frame must pivot easilyIdentify the Short Cable 71. It has a closed loop on Nylon LocknutShown One end and a threaded shaft on the other Press Top FrameStep A 3/8 Nylon Locknut LocknutEnd and a loop on the other Butterfly BaseBase 61 with a 3/8 x 2 Bolt 35 and a 3/8 Nylon Locknut BracketEr Pulley will be attached to the Bolt Frame 52 with a 3/8 x 3 1/4 Bolt 28, a 3/8 Flat Washer 17, and a 3/8 Nylon LocknutIs oriented as shown Secure them with the Nylon LocknutLocate and open the parts bag labelled Seat Assembly Secure it with a 1/4 Flat Washer 11 and a 1/4 Nylon LocknutSeat 51 with two 1/4 x 3/4 Screws ADJUSTMENT, beginning on page 21 of this manual Maintenance onApply the Weider PRO 9930 decal in the location shown PROCable Diagrams Cable ID Chart71 1.9m 6 ft 72 3.5m 11 ft 73 7.6m 24 ft Long Cable Adjustment Cable with two Cable Clips. Adjust the lengthCise will be reduced Nylon Strap 56 can be attached in the same mannerTROUBLE-SHOOTING and Maintenance Ed, move the other PulleyWeight Resistance Chart High Arm Butterfly Curl Leg Raise Weight Pulley Press LbsPlates Lbs Top Ordering Replacement Parts Part No R0501ARemove this Part Identification Chart from the Manual R0501APart Identification CHART-Model No. WESY99300 X 1 1/2 Carriage Bolt Pulley 21 Not shown to scalePage Remove this Part LIST/EXPLODED Drawing from the Manual Qty Description Key No. Qty Long CableModel No. WESY99300