Weider WESY99300 Locate and open the parts bag labelled Frame Assembly, Head of each Bolt

Page 6

Frame Assembly

1.Before beginning, make sure that you have read and understood the information on page 5.

Locate and open the parts bag labelled “FRAME ASSEMBLY.”

Press a 2” Square Inner Cap (38) into the Butterfly Base (61). Press two 2” Square Inner Caps into the Press Base (60).

Insert four 5/16” x 2 1/2” Carriage Bolts (1) up through the indicated holes in the Butterfly Base (61)

and the Press Base (60).

Note: If the Bolts fall out,

secure them by putting a small piece of tape over

the head of each Bolt.

Place the Butterfly Base and

the Press Base flat on the floor.

 

Attach the Press Base (60) to the Butterfly Base (61) with two 5/16” x 2 3/4” Bolts (20), two 5/16” Flat Washers (19), and two 5/16” Nylon Locknuts (2).

2.Position the Butterfly Upright (62) as shown. Place the bracket on the lower end of the Butterfly Upright

over the indicated 5/16” x 2 1/2” Carriage Bolts (1) in the Butterfly Base (61). Hand tighten two 5/16” Nylon

Locknuts (2) onto the Bolts.

Do not tighten the

 

Nylon Locknuts yet.

 

 

Place the bracket on the lower end of the Press

 

Frame Upright (59) over the indicated 5/16” x 2 1/2”

 

Carriage Bolts (1) in the Press Base (60). Hand tight-

 

en two 5/16” Nylon Locknuts (2) onto the Bolts.

Do

not tighten the Nylon Locknuts yet.

 

 

1

 

 

38

 

19

2

20

 

61

60

 

 

38

 

2

1

1

1

 

1

 

38

 

2

 

Position with the bracket on this side

62

59

2

2

1

1

61 60

6

Image 6
Contents Model No. WESY99300 Serial No Our factoryTable of Contents Limited WarrantyKeep hands and feet away from moving parts Important PrecautionsRead all instructions in this manual New decal in the appropriate locationUsing the weight system Before YOU BeginAssembly Locate and open the parts bag labelled Frame Assembly Head of each BoltDo not tighten Nylon Locknuts yet Into the top of the Butterfly Top Frame Attach the Weight Guides 58 to the Butterfly BasePin Grooves 1717 4Lubricate Flat Washers 19, and two 5/16 Nylon LocknutsTwo 5/16 Nylon Locknuts ClosestTighten all nylon locknuts used in steps 1 through Press Base. This will be a tight fit Locate and open the parts bag labelled ARMBushings should fit onto the ends of the tube Locknut the Press Frame must pivot easilyIdentify the Short Cable 71. It has a closed loop on Nylon LocknutShown One end and a threaded shaft on the other Press Top FrameStep End and a loop on the other A 3/8 Nylon LocknutLocknut Butterfly BaseBase 61 with a 3/8 x 2 Bolt 35 and a 3/8 Nylon Locknut BracketEr Pulley will be attached to the Bolt Is oriented as shown Frame 52 with a 3/8 x 3 1/4 Bolt 28, a 3/8 FlatWasher 17, and a 3/8 Nylon Locknut Secure them with the Nylon LocknutLocate and open the parts bag labelled Seat Assembly Secure it with a 1/4 Flat Washer 11 and a 1/4 Nylon LocknutSeat 51 with two 1/4 x 3/4 Screws Apply the Weider PRO 9930 decal in the location shown ADJUSTMENT, beginning on page 21 of this manualMaintenance on PROCable Diagrams Cable ID Chart71 1.9m 6 ft 72 3.5m 11 ft 73 7.6m 24 ft Long Cable Cise will be reduced AdjustmentCable with two Cable Clips. Adjust the length Nylon Strap 56 can be attached in the same mannerTROUBLE-SHOOTING and Maintenance Ed, move the other PulleyWeight Resistance Chart High Arm Butterfly Curl Leg Raise Weight Pulley Press LbsPlates Lbs Top Ordering Replacement Parts Part No R0501ARemove this Part Identification Chart from the Manual R0501APart Identification CHART-Model No. WESY99300 X 1 1/2 Carriage Bolt Pulley 21 Not shown to scalePage Remove this Part LIST/EXPLODED Drawing from the Manual Qty Description Key No. Qty Long CableModel No. WESY99300