Weider WESY99300 user manual TROUBLE-SHOOTING and Maintenance, Ed, move the other Pulley

Page 22

TROUBLE-SHOOTING AND MAINTENANCE

Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use sol- vents.

TIGHTENING THE CABLES

The type of cable used on weight systems can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. Slack can be removed from the cables in several differ- ent ways:

Moving one or both of the 3 1/2” Pulleys (5) to a different

 

 

 

 

set of holes in the Adjustable Pulley Plates (44) will tight-

 

 

 

35

en the cables.

 

 

 

 

To move one of the 3 1/2” Pulleys (5), remove the 3/8”

 

 

44

 

 

 

 

 

Nylon Locknut (4), 3/8” x 2” Bolt (35), Cable Trap (39),

 

 

 

Adjustment

and Pulley from the Adjustable Pulley Plates (44). Re-

 

4

 

 

 

Holes

attach the Pulley and Cable Trap to the other hole in the

 

 

 

5

Pulley Plates.

Note: If additional adjustment is need-

 

 

 

 

 

 

 

ed, move the other Pulley.

 

39

 

 

 

 

 

 

 

Slack can be removed from the Long Cable (73) by relo-

 

 

 

 

cating the indicated 3 1/2” Pulley (5) on the Press Seat

 

 

52

 

Frame (52). To do this, remove the 3/8” Nylon Locknut

 

 

 

 

(4), 3/8” Flat Washer (17), and 3/8” x 2 1/2” Bolt (6). Re-

4

 

 

 

attach the Pulley at the second or third hole, as needed.

 

 

 

 

 

 

 

 

 

17

14

 

5

 

 

 

 

 

 

 

 

 

 

73

 

 

 

 

6

 

The threaded shaft on the Medium Cable (72) attached to

 

 

 

 

the Weights (8) can also be used to tighten the cables.

 

 

 

 

To tighten the Medium Cable (72), remove the Small “U”-

 

 

72

 

 

 

2

 

Bracket (43) by removing the 5/16” Nylon Locknut (2) and

 

 

 

 

 

 

72

the 5/16” x 1 3/4” Bolt (9).

 

 

43

 

 

 

See the inset drawing. Tighten the 1/4” Nylon Locknut

 

 

9

 

 

 

 

 

(16) at the end of the Medium Cable (72) as far as it will

 

 

 

8

go. Then re-attach the Small “U”-Bracket (43).

 

 

 

 

 

 

 

 

16

 

 

 

 

 

43

If a cable slips off the pulleys often, the cable may have become twisted. Remove the cable and re-install it. If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.

22

Image 22
Contents Model No. WESY99300 Serial No Our factoryTable of Contents Limited WarrantyKeep hands and feet away from moving parts Important PrecautionsRead all instructions in this manual New decal in the appropriate locationUsing the weight system Before YOU BeginAssembly Head of each Bolt Locate and open the parts bag labelled Frame AssemblyDo not tighten Nylon Locknuts yet Into the top of the Butterfly Top Frame Attach the Weight Guides 58 to the Butterfly BasePin Grooves 1717 4Lubricate Flat Washers 19, and two 5/16 Nylon LocknutsClosest Two 5/16 Nylon LocknutsTighten all nylon locknuts used in steps 1 through Press Base. This will be a tight fit Locate and open the parts bag labelled ARMBushings should fit onto the ends of the tube Locknut the Press Frame must pivot easilyNylon Locknut Identify the Short Cable 71. It has a closed loop onShown Press Top Frame One end and a threaded shaft on the otherStep End and a loop on the other A 3/8 Nylon LocknutLocknut Butterfly BaseBase 61 with a 3/8 x 2 Bolt 35 and a 3/8 Nylon Locknut BracketEr Pulley will be attached to the Bolt Is oriented as shown Frame 52 with a 3/8 x 3 1/4 Bolt 28, a 3/8 FlatWasher 17, and a 3/8 Nylon Locknut Secure them with the Nylon LocknutLocate and open the parts bag labelled Seat Assembly Secure it with a 1/4 Flat Washer 11 and a 1/4 Nylon LocknutSeat 51 with two 1/4 x 3/4 Screws Apply the Weider PRO 9930 decal in the location shown ADJUSTMENT, beginning on page 21 of this manualMaintenance on PROCable ID Chart Cable Diagrams71 1.9m 6 ft 72 3.5m 11 ft 73 7.6m 24 ft Long Cable Cise will be reduced AdjustmentCable with two Cable Clips. Adjust the length Nylon Strap 56 can be attached in the same mannerTROUBLE-SHOOTING and Maintenance Ed, move the other PulleyHigh Arm Butterfly Curl Leg Raise Weight Pulley Press Lbs Weight Resistance ChartPlates Lbs Top Ordering Replacement Parts Part No R0501ARemove this Part Identification Chart from the Manual R0501APart Identification CHART-Model No. WESY99300 X 1 1/2 Carriage Bolt Pulley 21 Not shown to scalePage Remove this Part LIST/EXPLODED Drawing from the Manual Qty Description Key No. Qty Long CableModel No. WESY99300