Weider WESY99300 Locate and open the parts bag labelled ARM, Press Base. This will be a tight fit

Page 9

Arm Assembly

9

 

 

 

 

 

 

 

 

 

9. Locate and open the parts bag labelled “ARM

 

 

53

30

 

 

 

 

 

ASSEMBLY.”

 

 

 

 

 

Lubricate

 

 

 

 

 

 

Press a 1” x 7/8” Plastic Bushing (29) onto each weld-

 

4

 

 

 

ed spacer on the Press Frame (53). Slide the Press

 

 

 

 

 

Frame onto the Press Base (60). (See the inset draw-

 

 

 

29

 

ing for proper orientation.)

Note: The Plastic

 

 

 

53

 

 

 

 

Bushings should fit onto the ends of the tube in

 

 

 

 

 

Tube

 

 

 

the Press Base. This will be a tight fit.

 

 

 

 

 

60

 

 

 

 

 

 

 

 

 

Lubricate the 3/8” x 8” Bolt (30). Attach the Press

 

 

 

 

 

Frame (53) to the Press Base (60) with the Bolt and a

10

 

 

 

 

3/8” Nylon Locknut (4).

Do not overtighten the Nylon

 

 

37

 

 

 

 

 

Locknut; the Press Frame must pivot easily.

 

 

 

 

80

10. Press a 1 3/4” Square Inner Cap (37) into the top of a

 

 

 

 

 

Press Arm (54). Press a 1” Inner Cap (80) into the

 

 

 

 

 

indicated hole in the Press Arm.

 

 

37

 

 

 

 

 

 

 

 

 

Attach the Press Arm (54) to the bracket on the Press

 

 

 

 

 

Frame (53) with two 5/16” x 2 1/2” Bolts (3) and two

 

80

 

54

 

5/16” Nylon Locknuts (2).

 

 

 

 

 

 

 

 

 

 

Repeat this step to assemble the second Press Arm

 

 

 

 

 

(54).

 

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

53

 

11. Press a 1 1/2” Square Inner Cap (79) into the Press

11

 

 

 

 

Seat Frame (52).

 

 

 

 

 

 

 

 

 

 

 

Slide the bracket on the lower end of the Press Seat

 

 

 

2

 

 

 

 

 

 

Frame (52) onto the indicated 5/16” x 2 1/2” Carriage

 

59

 

52

 

Bolts (1) in the Press Base (60). Tighten two 5/16”

 

 

 

79

Nylon Locknuts (2) onto the Bolts.

 

 

 

 

 

Attach the Press Seat Frame (52) to the Press Frame

20

19

 

 

 

 

 

 

 

Upright (59) with two 5/16” x 2 3/4” Bolts (20), two

 

 

2

2

 

5/16” Flat Washers (19), and two 5/16” Nylon

 

 

 

 

 

 

 

 

 

Locknuts (2).

 

 

 

 

 

 

 

 

 

19

 

 

 

 

 

 

 

1

 

60

 

 

 

 

 

 

9

Image 9
Contents Our factory Model No. WESY99300 Serial NoLimited Warranty Table of ContentsRead all instructions in this manual Important PrecautionsKeep hands and feet away from moving parts New decal in the appropriate locationBefore YOU Begin Using the weight systemAssembly Locate and open the parts bag labelled Frame Assembly Head of each BoltDo not tighten Nylon Locknuts yet Pin Grooves 1717 4Lubricate Attach the Weight Guides 58 to the Butterfly BaseInto the top of the Butterfly Top Frame Flat Washers 19, and two 5/16 Nylon LocknutsTwo 5/16 Nylon Locknuts ClosestTighten all nylon locknuts used in steps 1 through Bushings should fit onto the ends of the tube Locate and open the parts bag labelled ARMPress Base. This will be a tight fit Locknut the Press Frame must pivot easilyIdentify the Short Cable 71. It has a closed loop on Nylon LocknutShown One end and a threaded shaft on the other Press Top FrameStep Locknut A 3/8 Nylon LocknutEnd and a loop on the other Butterfly BaseBracket Base 61 with a 3/8 x 2 Bolt 35 and a 3/8 Nylon LocknutEr Pulley will be attached to the Bolt Washer 17, and a 3/8 Nylon Locknut Frame 52 with a 3/8 x 3 1/4 Bolt 28, a 3/8 FlatIs oriented as shown Secure them with the Nylon LocknutSecure it with a 1/4 Flat Washer 11 and a 1/4 Nylon Locknut Locate and open the parts bag labelled Seat AssemblySeat 51 with two 1/4 x 3/4 Screws Maintenance on ADJUSTMENT, beginning on page 21 of this manualApply the Weider PRO 9930 decal in the location shown PROCable Diagrams Cable ID Chart71 1.9m 6 ft 72 3.5m 11 ft 73 7.6m 24 ft Long Cable Cable with two Cable Clips. Adjust the length AdjustmentCise will be reduced Nylon Strap 56 can be attached in the same mannerEd, move the other Pulley TROUBLE-SHOOTING and MaintenanceWeight Resistance Chart High Arm Butterfly Curl Leg Raise Weight Pulley Press LbsPlates Lbs Top Part No R0501A Ordering Replacement PartsR0501A Remove this Part Identification Chart from the ManualPart Identification CHART-Model No. WESY99300 Pulley 21 Not shown to scale X 1 1/2 Carriage BoltPage Remove this Part LIST/EXPLODED Drawing from the Manual Long Cable Qty Description Key No. QtyModel No. WESY99300