Weider WESY99300 user manual Seat 51 with two 1/4 x 3/4 Screws

Page 17

36.Insert a 1/4” x 1 1/2” Carriage Bolt (82) into the center hole in a Seat Plate (42). Attach the Seat Plate to a

Seat (51) with two 1/4” x 3/4” Screws (13).

Insert the 1/4” x 1 1/2” Carriage Bolt (82) into the indi- cated hole in the Seat Bar (74) and secure it with a

1/4” Flat Washer (11) and a 1/4” Nylon Locknut (16). Secure the other end of the Seat (51) with a 1/4” x

1 1/2” Screw (88) and a 1/4” Flat Washer.

37.Attach the Backrest (66) to the Butterfly Upright (62) with two 1/4” x 2 1/2” Screws (10) and two 1/4” Flat Washers (11).

38.Attach the Curl Pad (69) to the Curl Post (70) with two 1/4” x 3/4” Screws (13).

Insert the Curl Post (70) into the Seat Brace (75) and secure the Curl Post at the desired height with the Adjustment Knob (45).

36	51
	51
	82	74
	42	74
13
	11
16		88
37		11
		11
		10
66	62
		11
38	69
	69
		70
		13
	45
		75

Image 17

Contents Our factory Model No. WESY99300 Serial NoLimited Warranty Table of ContentsRead all instructions in this manual Important PrecautionsKeep hands and feet away from moving parts New decal in the appropriate locationBefore YOU Begin Using the weight systemAssembly Do not tighten Nylon Locknuts yet Locate and open the parts bag labelled Frame AssemblyHead of each Bolt Pin Grooves 1717 4Lubricate Attach the Weight Guides 58 to the Butterfly BaseInto the top of the Butterfly Top Frame Flat Washers 19, and two 5/16 Nylon LocknutsTighten all nylon locknuts used in steps 1 through Two 5/16 Nylon LocknutsClosest Bushings should fit onto the ends of the tube Locate and open the parts bag labelled ARMPress Base. This will be a tight fit Locknut the Press Frame must pivot easilyShown Identify the Short Cable 71. It has a closed loop onNylon Locknut Step One end and a threaded shaft on the otherPress Top Frame Locknut A 3/8 Nylon LocknutEnd and a loop on the other Butterfly BaseBracket Base 61 with a 3/8 x 2 Bolt 35 and a 3/8 Nylon LocknutEr Pulley will be attached to the Bolt Washer 17, and a 3/8 Nylon Locknut Frame 52 with a 3/8 x 3 1/4 Bolt 28, a 3/8 FlatIs oriented as shown Secure them with the Nylon LocknutSecure it with a 1/4 Flat Washer 11 and a 1/4 Nylon Locknut Locate and open the parts bag labelled Seat AssemblySeat 51 with two 1/4 x 3/4 Screws Maintenance on ADJUSTMENT, beginning on page 21 of this manualApply the Weider PRO 9930 decal in the location shown PRO71 1.9m 6 ft 72 3.5m 11 ft 73 7.6m 24 ft Cable DiagramsCable ID Chart Long Cable Cable with two Cable Clips. Adjust the length AdjustmentCise will be reduced Nylon Strap 56 can be attached in the same mannerEd, move the other Pulley TROUBLE-SHOOTING and MaintenancePlates Lbs Top Weight Resistance ChartHigh Arm Butterfly Curl Leg Raise Weight Pulley Press Lbs Part No R0501A Ordering Replacement PartsR0501A Remove this Part Identification Chart from the ManualPart Identification CHART-Model No. WESY99300 Pulley 21 Not shown to scale X 1 1/2 Carriage BoltPage Remove this Part LIST/EXPLODED Drawing from the Manual Long Cable Qty Description Key No. QtyModel No. WESY99300