Weider WESY99300 user manual Two 5/16 Nylon Locknuts, Closest

Page 8

6.Attach the Butterfly Top Frame (64) and the Press Top Frame (63) to the indicated brackets on the

Uprights (59, 62) with four 5/16” x 2 3/4” Bolts (20), two Top Plates (46), and four 5/16” Nylon Locknuts

(2). Note: Before attaching the Top Frames to the

Uprights, make sure that both Weight Guides (58) are inside of the indicated holes. Do not tighten

the Nylon Locknuts yet.

Secure the Weight Guides (58) to the Butterfly Top

Frame (64) with two 3/8” x 2 1/2” Bolts (6), four 3/8” Flat Washers (17), and two 3/8” Jam Nuts (18).

7.Turn the Seat Brace (75) so the nut is on the side shown. Attach the Seat Brace to the Butterfly Base

(61)with the indicated 5/16” x 2 1/2” Carriage Bolts

(1) and two 5/16” Nylon Locknuts (2).

Do not tighten

the Nylon Locknuts yet.

 

8. Hold the Seat Bar (74) between the Seat Brace (75) and the Butterfly Upright (62) so that the hole that is

closest

to a welded plate is toward the Seat Brace.

Attach the Seat Bar to the Seat Brace with two 5/16”

x 2 3/4” Bolts (20), two 5/16” Flat Washers (19), and

two 5/16” Nylon Locknuts (2).

Do not tighten the

Nylon Locknuts yet. Note: Be careful not to over- tighten the Nylon Locknuts, or the curl post attached in step 38 will not slide freely.

Attach the Seat Bar (74) to the Butterfly Upright (62) with two 5/16” x 2 3/4” Bolts (20), two 5/16” Flat Washers (19), and two 5/16” Nylon Locknuts (2).

Tighten all nylon locknuts used in steps 1 through 8.

6

 

 

20

18

20

 

17

17

 

46

 

46

 

 

64

 

63

 

 

17

Holes

17

 

6

 

 

58

 

 

2

2

 

 

62

 

59

 

 

7

Nut

 

 

 

75

 

 

 

2

 

 

 

61

 

1

 

8

 

 

 

62

 

2

 

19

 

20

Hole

 

 

74

 

 

 

 

19

19

75

 

 

 

20

 

 

8

Image 8
Contents Model No. WESY99300 Serial No Our factoryTable of Contents Limited WarrantyImportant Precautions Read all instructions in this manualKeep hands and feet away from moving parts New decal in the appropriate locationUsing the weight system Before YOU BeginAssembly Do not tighten Nylon Locknuts yet Locate and open the parts bag labelled Frame AssemblyHead of each Bolt Attach the Weight Guides 58 to the Butterfly Base Pin Grooves 1717 4LubricateInto the top of the Butterfly Top Frame Flat Washers 19, and two 5/16 Nylon LocknutsTighten all nylon locknuts used in steps 1 through Two 5/16 Nylon LocknutsClosest Locate and open the parts bag labelled ARM Bushings should fit onto the ends of the tubePress Base. This will be a tight fit Locknut the Press Frame must pivot easilyShown Identify the Short Cable 71. It has a closed loop onNylon Locknut Step One end and a threaded shaft on the otherPress Top Frame A 3/8 Nylon Locknut LocknutEnd and a loop on the other Butterfly BaseBase 61 with a 3/8 x 2 Bolt 35 and a 3/8 Nylon Locknut BracketEr Pulley will be attached to the Bolt Frame 52 with a 3/8 x 3 1/4 Bolt 28, a 3/8 Flat Washer 17, and a 3/8 Nylon LocknutIs oriented as shown Secure them with the Nylon LocknutLocate and open the parts bag labelled Seat Assembly Secure it with a 1/4 Flat Washer 11 and a 1/4 Nylon LocknutSeat 51 with two 1/4 x 3/4 Screws ADJUSTMENT, beginning on page 21 of this manual Maintenance onApply the Weider PRO 9930 decal in the location shown PRO71 1.9m 6 ft 72 3.5m 11 ft 73 7.6m 24 ft Cable DiagramsCable ID Chart Long Cable Adjustment Cable with two Cable Clips. Adjust the lengthCise will be reduced Nylon Strap 56 can be attached in the same mannerTROUBLE-SHOOTING and Maintenance Ed, move the other PulleyPlates Lbs Top Weight Resistance ChartHigh Arm Butterfly Curl Leg Raise Weight Pulley Press Lbs Ordering Replacement Parts Part No R0501ARemove this Part Identification Chart from the Manual R0501APart Identification CHART-Model No. WESY99300 X 1 1/2 Carriage Bolt Pulley 21 Not shown to scalePage Remove this Part LIST/EXPLODED Drawing from the Manual Qty Description Key No. Qty Long CableModel No. WESY99300