Weider WESY99300 user manual Base 61 with a 3/8 x 2 Bolt 35 and a 3/8 Nylon Locknut, Bracket

Page 13

22.Wrap the Long Cable (73) around a 3 1/2” Pulley (5) in the direction shown. Attach the Pulley and a Cable

Trap (39) to the Butterfly Upright (62) with a 3/8” x 3 3/4” Bolt (7), a 3/8” Flat Washer (17), and a 3/8”

Nylon Locknut (4). Make sure that the Cable Trap is oriented as shown.

Wrap the Long Cable (73) over a 3 1/2” Pulley (5) in the direction shown. Re-attach the Pulley and a Cable Trap (39) to the lower hole in the Adjustable Pulley

Plates (44) with a 3/8” x 2” Bolt (35) and a 3/8” Nylon Locknut (4). Make sure that the Cable Trap is ori- ented as shown.

23.Wrap the Long Cable (73) around a 3 1/2” Pulley (5) in the direction shown. Attach the Pulley and a Cable Trap (39) to the indicated bracket on the Butterfly

Base (61) with a 3/8” x 2” Bolt (35) and a 3/8” Nylon Locknut (4).

24.Wrap the Long Cable (73) around a 3 1/2” Pulley (5). Attach the Pulley and a Cable Trap (39) to the indicat- ed bracket on the Butterfly Base (61) with a 3/8” x 2” Bolt (35) and a 3/8” Nylon Locknut (4).

22
	44		35
	44
		4
	39	5
		5
	62
	4
	17
		39	5
		39
		73	7
			7
23
	73
35	5
			61
	39
	Bracket		4
			4
24
	35	5	73
		5	4
			4
		39
		61	Bracket

13

Image 13

Contents Our factory Model No. WESY99300 Serial NoLimited Warranty Table of ContentsRead all instructions in this manual Important PrecautionsKeep hands and feet away from moving parts New decal in the appropriate locationBefore YOU Begin Using the weight systemAssembly Head of each Bolt Locate and open the parts bag labelled Frame AssemblyDo not tighten Nylon Locknuts yet Pin Grooves 1717 4Lubricate Attach the Weight Guides 58 to the Butterfly BaseInto the top of the Butterfly Top Frame Flat Washers 19, and two 5/16 Nylon LocknutsClosest Two 5/16 Nylon LocknutsTighten all nylon locknuts used in steps 1 through Bushings should fit onto the ends of the tube Locate and open the parts bag labelled ARMPress Base. This will be a tight fit Locknut the Press Frame must pivot easilyNylon Locknut Identify the Short Cable 71. It has a closed loop onShown Press Top Frame One end and a threaded shaft on the otherStep Locknut A 3/8 Nylon LocknutEnd and a loop on the other Butterfly BaseBracket Base 61 with a 3/8 x 2 Bolt 35 and a 3/8 Nylon LocknutEr Pulley will be attached to the Bolt Washer 17, and a 3/8 Nylon Locknut Frame 52 with a 3/8 x 3 1/4 Bolt 28, a 3/8 FlatIs oriented as shown Secure them with the Nylon LocknutSecure it with a 1/4 Flat Washer 11 and a 1/4 Nylon Locknut Locate and open the parts bag labelled Seat AssemblySeat 51 with two 1/4 x 3/4 Screws Maintenance on ADJUSTMENT, beginning on page 21 of this manualApply the Weider PRO 9930 decal in the location shown PROCable ID Chart Cable Diagrams71 1.9m 6 ft 72 3.5m 11 ft 73 7.6m 24 ft Long Cable Cable with two Cable Clips. Adjust the length AdjustmentCise will be reduced Nylon Strap 56 can be attached in the same mannerEd, move the other Pulley TROUBLE-SHOOTING and MaintenanceHigh Arm Butterfly Curl Leg Raise Weight Pulley Press Lbs Weight Resistance ChartPlates Lbs Top Part No R0501A Ordering Replacement PartsR0501A Remove this Part Identification Chart from the ManualPart Identification CHART-Model No. WESY99300 Pulley 21 Not shown to scale X 1 1/2 Carriage BoltPage Remove this Part LIST/EXPLODED Drawing from the Manual Long Cable Qty Description Key No. QtyModel No. WESY99300