Weider WESY99300 Attach the Weight Guides 58 to the Butterfly Base, Pin Grooves 1717 4Lubricate

Page 7

3.Place two Weight Bumpers (84) over the indicated holes in the Butterfly Base (61). Slide the Weight Guides (58) into the indicated holes.

Attach the Weight Guides (58) to the Butterfly Base

(61)with two 3/8” x 2 1/2” Bolts (6), four 3/8” Flat Washers (17), and two 3/8” Jam Nuts (18).

Slide the eight Weights (8) onto the Weight Guides (58). Make sure that the Weights are turned so the pin grooves are on the bottoms of the Weights.

4.Press a Weight Tube Bumper (76) into the lower end of the Weight Tube (77). Slide the Weight Tube into the center hole in the Weights (8).

Lubricate the holes in the Top Weight (78). Slide the Top Weight onto the Weight Guides (58).

3

58

8

Pin

Grooves

84

18

18

1717

61

17

6

4Lubricate

78

58

77

76

8

5. Press two 2” Square Inner Caps (38) into the Butterfly

5

 

 

 

 

Top Frame (64). Press two 1” Round Inner Caps (41)

 

 

38

 

 

 

 

 

into the top of the Butterfly Top Frame.

 

 

 

 

 

 

2

19

20

 

 

 

 

 

Attach the Butterfly Top Frame (64) to the Press Top

38

41

64

 

19

Frame (63) with two 5/16” x 2 3/4” Bolts (20), two

 

 

 

 

 

5/16” Flat Washers (19), and two 5/16” Nylon

 

 

 

 

63

 

 

 

 

 

Locknuts (2).

 

 

 

 

 

Press a 2” Square Inner Cap (38) into the Press Top

 

 

38

2

 

 

 

 

 

Frame (63).

 

 

 

 

 

 

7

 

 

 

 

Image 7
Contents Our factory Model No. WESY99300 Serial NoLimited Warranty Table of ContentsNew decal in the appropriate location Important PrecautionsRead all instructions in this manual Keep hands and feet away from moving partsBefore YOU Begin Using the weight systemAssembly Head of each Bolt Locate and open the parts bag labelled Frame AssemblyDo not tighten Nylon Locknuts yet Flat Washers 19, and two 5/16 Nylon Locknuts Attach the Weight Guides 58 to the Butterfly BasePin Grooves 1717 4Lubricate Into the top of the Butterfly Top FrameClosest Two 5/16 Nylon LocknutsTighten all nylon locknuts used in steps 1 through Locknut the Press Frame must pivot easily Locate and open the parts bag labelled ARMBushings should fit onto the ends of the tube Press Base. This will be a tight fitNylon Locknut Identify the Short Cable 71. It has a closed loop onShown Press Top Frame One end and a threaded shaft on the otherStep Butterfly Base A 3/8 Nylon LocknutLocknut End and a loop on the otherBracket Base 61 with a 3/8 x 2 Bolt 35 and a 3/8 Nylon LocknutEr Pulley will be attached to the Bolt Secure them with the Nylon Locknut Frame 52 with a 3/8 x 3 1/4 Bolt 28, a 3/8 FlatWasher 17, and a 3/8 Nylon Locknut Is oriented as shownSecure it with a 1/4 Flat Washer 11 and a 1/4 Nylon Locknut Locate and open the parts bag labelled Seat AssemblySeat 51 with two 1/4 x 3/4 Screws PRO ADJUSTMENT, beginning on page 21 of this manualMaintenance on Apply the Weider PRO 9930 decal in the location shownCable ID Chart Cable Diagrams71 1.9m 6 ft 72 3.5m 11 ft 73 7.6m 24 ft Long Cable Nylon Strap 56 can be attached in the same manner AdjustmentCable with two Cable Clips. Adjust the length Cise will be reducedEd, move the other Pulley TROUBLE-SHOOTING and MaintenanceHigh Arm Butterfly Curl Leg Raise Weight Pulley Press Lbs Weight Resistance ChartPlates Lbs Top Part No R0501A Ordering Replacement PartsR0501A Remove this Part Identification Chart from the ManualPart Identification CHART-Model No. WESY99300 Pulley 21 Not shown to scale X 1 1/2 Carriage BoltPage Remove this Part LIST/EXPLODED Drawing from the Manual Long Cable Qty Description Key No. QtyModel No. WESY99300