Weider WESY99300 Identify the Short Cable 71. It has a closed loop on, Nylon Locknut, Shown

Page 10

12.Press two 1 1/2” Square Inner Caps (79) into the Leg Lever (49). Insert a Bumper (33) between the brackets on the Leg Lever. Attach the Bumper to the Leg Lever with a #10 x 1” Screw (32).

Slide the bracket on the Leg Lever (49) onto the Press

Seat Frame (52). Attach the Leg Lever to the Press Seat

Frame with a 5/16” x 2 1/4” Bolt (81) and a 5/16” Jam

Nut (90). Do not overtighten the Jam Nut. The Leg

Lever must pivot easily.

Attach a 3/8” x 2 1/2” Eyebolt (83) to the Leg Lever (49) with a 3/8” Flat Washer (17) and 3/8” Nylon Locknut (4).

13.Press a 1 3/4” Square Inner Cap (37) into each end of the Right Butterfly Arm (68). Wet the lower end of the Arm with soapy water. Slide a 10” Pad (65) onto the lower end of the Arm.

Lubricate the indicated axle on the Butterfly Top Frame

(64). Have a second person slide the Right Butterfly Arm

(68) onto the axle, as shown. Refer to the inset draw-

ing. Place two 1” Retainers (25), with the teeth down- ward, on top of an inverted 1” Round Cap (26). Using

a hammer, tap the 1” Round Cap and the Retainers onto the axle to secure the Right Butterfly Arm.

Repeat this step to assemble the Left Butterfly Arm (67).

Cable Assembly

14.Open the parts bag labelled “CABLE ASSEMBLY AND PULLEYS.” For cable identification and routing during steps 14–32, refer to the CABLE DIAGRAMS and CABLE ID CHART on pages 19 and 20.

Insert two 3/8” x 1” Bolts (15) into the welded brackets on the Left and Right Butterfly Arms (67, 68). Secure each Bolt with a 3/8” Jam Nut (18).

Identify the Short Cable (71). It has a closed loop on

each end. Slide one end of the Cable onto each of the 3/8” x 1” Bolts (15). Secure the Cable to the Bolts with 3/8” Jam Nuts (18). Do not overtighten the Jam Nuts.

Remove both 3 1/2” Pulleys (5) from the pre-assembled Adjustable Pulley Plates (44). Wrap the Short Cable (71) around a Pulley in the direction shown. Attach the Pulley and a Cable Trap (39) to the top hole in the two

Adjustable Pulley Plates with a 3/8” x 2” Bolt (35) and a

3/8” Nylon Locknut (4).

Make

sure that the Cable Trap

and the Pulley Plates are oriented as

shown.

10

12

52

 

 

 

 

 

 

 

90

81

 

 

 

 

32

 

 

 

 

 

79

 

33

 

49

 

 

17

 

 

83

 

 

4

 

 

 

 

 

 

79

13

64

 

 

 

 

 

Lubricate

 

 

 

25

 

 

68

26

37

67

 

 

37

 

 

 

 

 

64

 

65

 

25

 

 

 

 

 

 

Teeth

 

 

 

26

 

14

15

15

 

 

 

 

68

18

 

71

 

67

18

 

 

 

 

5

 

 

39

 

35

 

4

 

44

 

 

 

Image 10
Contents Model No. WESY99300 Serial No Our factoryTable of Contents Limited WarrantyKeep hands and feet away from moving parts Important PrecautionsRead all instructions in this manual New decal in the appropriate locationUsing the weight system Before YOU BeginAssembly Head of each Bolt Locate and open the parts bag labelled Frame AssemblyDo not tighten Nylon Locknuts yet Into the top of the Butterfly Top Frame Attach the Weight Guides 58 to the Butterfly BasePin Grooves 1717 4Lubricate Flat Washers 19, and two 5/16 Nylon LocknutsClosest Two 5/16 Nylon LocknutsTighten all nylon locknuts used in steps 1 through Press Base. This will be a tight fit Locate and open the parts bag labelled ARMBushings should fit onto the ends of the tube Locknut the Press Frame must pivot easilyNylon Locknut Identify the Short Cable 71. It has a closed loop onShown Press Top Frame One end and a threaded shaft on the otherStep End and a loop on the other A 3/8 Nylon LocknutLocknut Butterfly BaseBase 61 with a 3/8 x 2 Bolt 35 and a 3/8 Nylon Locknut BracketEr Pulley will be attached to the Bolt Is oriented as shown Frame 52 with a 3/8 x 3 1/4 Bolt 28, a 3/8 FlatWasher 17, and a 3/8 Nylon Locknut Secure them with the Nylon LocknutLocate and open the parts bag labelled Seat Assembly Secure it with a 1/4 Flat Washer 11 and a 1/4 Nylon LocknutSeat 51 with two 1/4 x 3/4 Screws Apply the Weider PRO 9930 decal in the location shown ADJUSTMENT, beginning on page 21 of this manualMaintenance on PROCable ID Chart Cable Diagrams71 1.9m 6 ft 72 3.5m 11 ft 73 7.6m 24 ft Long Cable Cise will be reduced AdjustmentCable with two Cable Clips. Adjust the length Nylon Strap 56 can be attached in the same mannerTROUBLE-SHOOTING and Maintenance Ed, move the other PulleyHigh Arm Butterfly Curl Leg Raise Weight Pulley Press Lbs Weight Resistance ChartPlates Lbs Top Ordering Replacement Parts Part No R0501ARemove this Part Identification Chart from the Manual R0501APart Identification CHART-Model No. WESY99300 X 1 1/2 Carriage Bolt Pulley 21 Not shown to scalePage Remove this Part LIST/EXPLODED Drawing from the Manual Qty Description Key No. Qty Long CableModel No. WESY99300