Weider WESY99300 user manual Frame 52 with a 3/8 x 3 1/4 Bolt 28, a 3/8 Flat, Is oriented as shown

Page 15

29.Wrap the Long Cable (73) around a “V” Pulley (21) in the direction shown. Attach the “V” Pulley and a Long Cable Trap (14) to the small tube on the Press Seat

Frame (52) with a 3/8” x 3 1/4” Bolt (28), a 3/8” Flat

Washer (17), and a 3/8” Nylon Locknut (4).

Note: The

small tube has three adjustment holes. Mount the

 

“V” Pulley in the hole farthest from the Press

 

Frame Upright (59). Make sure that the Cable Trap

 

is oriented as shown.

 

30.Wrap the Long Cable (73) around a 3 1/2” Pulley (5) in the direction shown. Attach the Pulley and a Cable Trap (39) to the indicated hole in the Press Frame

(53)with a 3/8” x 3 1/4” Bolt (28), a 3/8” Flat Washer

(17), and a 3/8” Nylon Locknut (4). Make sure that

the Pulley is mounted on the inside of the Press Frame and that the Cable Trap is oriented as shown.

31.Route the Long Cable (73) around a 3 1/2” Pulley (5) and back through the opening in the Press Frame (53).

Remove the 3/8” Nylon Locknut (4) from the 3/8” x

 

4 3/4” Bolt (23) that was inserted in step 27. Attach

 

the Pulley and a Cable Trap (39) to the Bolt and

 

secure them with the Nylon Locknut.

Make sure that

the Cable Trap is oriented as shown.

 

32.Note: Lift the Top Weight (78) on the weight stack in order to create slack in the Long Cable (73) before beginning this step.

Attach the Long Cable (73) to the Leg Lever (49) by slipping the looped end of the Cable onto the looped end of the 3/8” x 2 1/2” Eyebolt (83).

29

 

59

 

 

 

52

 

 

 

4

 

 

 

17

 

 

 

14

 

 

 

21

 

 

 

28

 

 

 

73

 

30

 

 

 

 

 

73

 

 

 

4

 

17

 

 

 

28

 

5

 

 

 

39

 

 

53

 

 

31

 

 

 

 

39

 

 

 

 

53

 

 

5

23

 

 

 

 

4

 

73

 

 

 

 

32

 

 

 

 

 

83

49

 

 

73

 

15

Image 15
Contents Our factory Model No. WESY99300 Serial NoLimited Warranty Table of ContentsNew decal in the appropriate location Important PrecautionsRead all instructions in this manual Keep hands and feet away from moving partsBefore YOU Begin Using the weight systemAssembly Locate and open the parts bag labelled Frame Assembly Head of each BoltDo not tighten Nylon Locknuts yet Flat Washers 19, and two 5/16 Nylon Locknuts Attach the Weight Guides 58 to the Butterfly BasePin Grooves 1717 4Lubricate Into the top of the Butterfly Top FrameTwo 5/16 Nylon Locknuts ClosestTighten all nylon locknuts used in steps 1 through Locknut the Press Frame must pivot easily Locate and open the parts bag labelled ARMBushings should fit onto the ends of the tube Press Base. This will be a tight fitIdentify the Short Cable 71. It has a closed loop on Nylon LocknutShown One end and a threaded shaft on the other Press Top FrameStep Butterfly Base A 3/8 Nylon LocknutLocknut End and a loop on the otherBracket Base 61 with a 3/8 x 2 Bolt 35 and a 3/8 Nylon LocknutEr Pulley will be attached to the Bolt Secure them with the Nylon Locknut Frame 52 with a 3/8 x 3 1/4 Bolt 28, a 3/8 FlatWasher 17, and a 3/8 Nylon Locknut Is oriented as shownSecure it with a 1/4 Flat Washer 11 and a 1/4 Nylon Locknut Locate and open the parts bag labelled Seat AssemblySeat 51 with two 1/4 x 3/4 Screws PRO ADJUSTMENT, beginning on page 21 of this manualMaintenance on Apply the Weider PRO 9930 decal in the location shownCable Diagrams Cable ID Chart71 1.9m 6 ft 72 3.5m 11 ft 73 7.6m 24 ft Long Cable Nylon Strap 56 can be attached in the same manner AdjustmentCable with two Cable Clips. Adjust the length Cise will be reducedEd, move the other Pulley TROUBLE-SHOOTING and MaintenanceWeight Resistance Chart High Arm Butterfly Curl Leg Raise Weight Pulley Press LbsPlates Lbs Top Part No R0501A Ordering Replacement PartsR0501A Remove this Part Identification Chart from the ManualPart Identification CHART-Model No. WESY99300 Pulley 21 Not shown to scale X 1 1/2 Carriage BoltPage Remove this Part LIST/EXPLODED Drawing from the Manual Long Cable Qty Description Key No. QtyModel No. WESY99300