Whirlpool 8577208 installation instructions Power Supply Cord, Four-wire electrical connection

Page 12

2.Remove hold-down screw and the terminal block cover.

A

CD

B

A. External ground conductor screw

B.Tab

C.Terminal block cover

D.Hold-down screw

3.Assemble ³⁄₄" UL-listed strain relief (UL marking on strain relief) into the hole below the terminal block opening. Tighten strain relief screws just enough to hold the two clamp sections together. Install power supply cord through the

B

A

C

A. Strain relief clamp sections

B. Dryer cabinet

C. Strain relief screws

strain relief.

4.Complete installation following instructions for your type of electrical connection:

Four-wire (recommended method)

Three-wire (if four-wire is not available)

Power Supply Cord, Four-wire electrical connection:

 

A

 

B

C

D

 

 

G

F

 

 

A. Spade terminals with upturned ends E

B.Neutral

C.³⁄₄" UL-listed strain relief

D.Neutral (white)

E.Ring terminals

F.Ground wire

G.Ground prong

Four-wire power supply cord must have four, No.-10 copper wires and match a four-wire receptacle of NEMA Type 14-30R. The fourth wire (ground conductor) must be identified by a green cover and the neutral conductor by a white cover.

5.Remove the center terminal block screw.

6.Remove the appliance neutral ground wire from the external ground conductor screw. Fasten under center, silver-colored terminal block screw.

7.Connect the ground wire of the power supply cord to the external ground conductor screw. Tighten screw.

8.Connect the neutral wire (white or center) of the power supply cord under the center screw of the terminal block. Tighten screw.

9.Connect the other wires to outer terminal block screws. Tighten screws.

10.Tighten strain relief screws.

11.Insert tab of the terminal block cover into slot of the dryer rear panel. Secure cover with hold-down screw.

AB

C

G

F

D

E

A.External ground conductor screw

B.Appliance neutral ground wire

C.Center terminal block screw

D.Outer terminal block screws

E.Strain relief screw

F.Neutral (center wire)

G.Ground wire

12

Image 12
Contents Table of Contents/Table des matières 8577208Dryer Safety What to do if YOU Smell GAS Recessed Area and Closet Installation Instructions Tools and PartsLocation Requirements Tools neededProduct Dimensions 27 68.6 cm dryer Product Dimensions 29 73.7 cm dryerMinimum Installation Clearances Recessed front viewElectrical Requirements Gas Dryer Electrical Requirements Electric DryerRecommended Ground Method Gas Supply Requirements Type of GasFor a grounded, cord-connected dryer Gas Supply Pressure Testing Venting RequirementsGas Supply Line Do not install screening or cap over the end of the vent Vent System Length Multiple Dryer VentingMaximum Vent Length If an exhaust hood cannot be usedInstall Coin Slide and Coin Box Complete InstallationConnect Vent Power Supply Cord Method U.S. Only Make Electrical ConnectionPower Supply Cord, Four-wire electrical connection Remove hold-down screw and the terminal block coverPower Supply Cord, Three-wire electrical connection EDCDirect Wire Method U.S. Only Direct Wire Four-wire electrical connectionDirect Wire Three-wire electrical connection Loosen or remove the center terminal block screwChanging to a 30- or 60-MINUTE Timing CAM Maintenance instructions If dryer does not operate check the followingIf you need assistance Page Sécurité DE LA Sécheuse Importantes Instructions DE Sécurité Exigences d’emplacement Outillage et piècesOutillage nécessaire Pièces fourniesDimensions du produit Sécheuse de 27 68,6 cm Dimensions du produit Sécheuse de 29 73,7 cmMéthode recommandée de liaison à la terre Spécifications électriques sécheuse à gazSpécifications électriques sécheuse électrique Spécifications de l’alimentation en gaz Exigences concernant l’évacuation Type de gazCanalisation de gaz Tests de pressurisation de la canalisation de gazLongueur du circuit dévacuation Évacuation multiple de la sécheuseLongueur maximale du conduit Installation dune glissière et Dune caisse à monnaie Si une bouche de décharge ne peut être utiliséeAchever l’installation Raccordement à la canalisation de gazRaccordement du conduit d’évacuation Installation d’une glissière et d’une Caisse à monnaie Raccordement électriqueMéthode du cordon d’alimentation É.-U. seulement Déconnecter la source de courant électriqueCordon d’alimentation, prise de courant à quatre conducteurs Ôter la vis de retenue et le couvercle du bloc de connexionCordon d’alimentation, prise de courant à trois conducteurs Méthode de câblage direct É.-U. seulement Câblage direct, prise de courant à quatre conducteursCâblage direct, prise de courant à trois conducteurs Trois conducteurs avec conducteur de liaisonInstallation D’UNE Came DE Minutage Pour 30 OU 60 Minutes Instructions d’entretien Si la sécheuse ne fonctionne pas, vérifier ce qui suitSi vous avez besoin d’aide 8577208