Whirlpool 8577208 Maintenance instructions, If dryer does not operate check the following

Page 17

Maintenance instructions:

Clean lint screen after each cycle.

Removing accumulated lint:

From inside the dryer cabinet:

Lint should be removed every 2 years or more often, depending on dryer usage. Cleaning should be done by a qualified person.

From the exhaust vent:

Lint should be removed every 2 years, or more often, depending on dryer usage.

If dryer does not operate check the following:

Electric supply is connected.

Circuit breaker is not tripped or house fuse is not blown.

Door is closed.

Controls are set in a running or “ON” position.

START button has been pushed firmly.

For gas dryers, check that gas supply shutoff valves are set in open position.

If you need assistance:

The Commercial Laundry Support Center will answer any questions about operating or maintaining your dryer not covered in the Installation Instructions. The Commercial Laundry Support Center is open 24 hours a day, 7 days a week. Just dial

1-800 NO BELTS (1-800-662-3587) — the call is toll free.

When you call, you will need the dryer model number and serial number. Both numbers can be found on the serial-rating plate located in the dryer door well.

17

Image 17
Contents 8577208 Table of Contents/Table des matièresDryer Safety What to do if YOU Smell GAS Tools and Parts Recessed Area and Closet Installation InstructionsLocation Requirements Tools neededProduct Dimensions 29 73.7 cm dryer Product Dimensions 27 68.6 cm dryerMinimum Installation Clearances Recessed front viewRecommended Ground Method Electrical Requirements Gas DryerElectrical Requirements Electric Dryer For a grounded, cord-connected dryer Gas Supply RequirementsType of Gas Gas Supply Line Gas Supply Pressure TestingVenting Requirements Vent System Length Multiple Dryer Venting Do not install screening or cap over the end of the ventMaximum Vent Length If an exhaust hood cannot be usedConnect Vent Install Coin Slide and Coin BoxComplete Installation Make Electrical Connection Power Supply Cord Method U.S. OnlyRemove hold-down screw and the terminal block cover Power Supply Cord, Four-wire electrical connectionEDC Power Supply Cord, Three-wire electrical connectionDirect Wire Four-wire electrical connection Direct Wire Method U.S. OnlyLoosen or remove the center terminal block screw Direct Wire Three-wire electrical connectionChanging to a 30- or 60-MINUTE Timing CAM If you need assistance Maintenance instructionsIf dryer does not operate check the following Page Sécurité DE LA Sécheuse Importantes Instructions DE Sécurité Outillage et pièces Exigences d’emplacementOutillage nécessaire Pièces fourniesDimensions du produit Sécheuse de 29 73,7 cm Dimensions du produit Sécheuse de 27 68,6 cmSpécifications électriques sécheuse électrique Méthode recommandée de liaison à la terreSpécifications électriques sécheuse à gaz Spécifications de l’alimentation en gaz Type de gaz Exigences concernant l’évacuationCanalisation de gaz Tests de pressurisation de la canalisation de gazLongueur maximale du conduit Longueur du circuit dévacuationÉvacuation multiple de la sécheuse Si une bouche de décharge ne peut être utilisée Installation dune glissière et Dune caisse à monnaieRaccordement du conduit d’évacuation Achever l’installationRaccordement à la canalisation de gaz Raccordement électrique Installation d’une glissière et d’une Caisse à monnaieMéthode du cordon d’alimentation É.-U. seulement Déconnecter la source de courant électriqueÔter la vis de retenue et le couvercle du bloc de connexion Cordon d’alimentation, prise de courant à quatre conducteursCordon d’alimentation, prise de courant à trois conducteurs Câblage direct, prise de courant à quatre conducteurs Méthode de câblage direct É.-U. seulementTrois conducteurs avec conducteur de liaison Câblage direct, prise de courant à trois conducteursInstallation D’UNE Came DE Minutage Pour 30 OU 60 Minutes Si vous avez besoin d’aide Instructions d’entretienSi la sécheuse ne fonctionne pas, vérifier ce qui suit 8577208