Miele PT 7136 PLUS installation manual Sort the laundry, Load the laundry

Page 12

Use

1. Sort the laundry

￿Loosen up the washed laundry.

￿For even drying results sort by desired dryness, fiber/fabric, size and residual moisture after spinning.

￿Do not dry items that may melt or ignite in the dryer such as plastics, rubber or sneakers. They could melt and damage the laundry.

Check hems and seams, be sure that no filling can come out.

Comforter covers and pillowcases should be fastened in order to prevent small items from getting trapped inside of them.

Close zippers, hooks and eyelets.

Tie fabric belts and apron ties.

Remove or sew up released bra underwires.

2. Load the laundry

￿Use the ￿ button to open the drum door.

￿Load the laundry loosely into the drum.

Do not overload the drum. Overloading strains the fabrics and results in poor drying.

To prevent fabric damage, check that laundry is not caught in the closed door. Do not use softener sheets in this dryer. Silicates contained in these sheets could cause the dryer to overheat.

￿Close the door with a firm swing or lean against the dryer and push it closed.

12

Image 12
Contents Operating and Installation manual Vented Dryer PT 7136 Plus Contents Contents Important Safety Instructions Important Safety Instructions Save These Instructions Guide to the dryer Control panelDisplay function Main menuJog shuttle Program selection possibilitySettings Menu Program selectionBasic menu of a drying program Before using for the first time Welcome screenLanguage Set the time of dayUse Fabric care labelsDrying tips Sort the laundry Load the laundrySelect Low temp. and/or Timer Select a programInsert coins if operated by coin mechanism Starting a programCleaning and care hints At the end of a programRemaining time Before the end of a programCanceling a program Coin mechanismAdding/removing laundry during a drying program Continue dryingProgram guide Woollen handcare SmoothingCool air Warm airJeans Normal, Hand ironShirts ProofingTimer Select the submenu TimerStarting the timer function Canceling the timerFavorites Selecting/Changing a FavoriteBasic menu Drying level programs Program Warm air, Cool airOther programs Low temp Saving a FavoriteAssigning a direct select button Cleaning and Care Cleaning the lint filterRemoving the lint filter Disassembling the lint filterClean the lint filters dry Clean the lint filters wetCleaning the exterior and the control panel Inserting the lint filterFrequently asked questions Check and fault messages in the displayWhat if Possible cause Solution What if Possible cause Solution At the end of a ProgramAppears Other faults What if Possible fault Solution What if there is Condensed waterDrum? Items madeWhat if Possible cause Solution Program cannot Start indicatorBe started, Display remainsChanging the light bulb After sales service Optional accessoriesInstallation Instructions Important Safety Instructions Save These Instructions Installation Front viewSide view Rear view Top view Washer/ Dryer Stack Installation on a cement base Coin mechanism Installation Transporting the dryer to the installation siteLevel the dryer Electrical connection Installation of exhaust venting General notesHow to calculate the effective duct length Tips about the ductwork Additional duct lengths 4 rigid pipe only Length Determining the position of the exhaust connection Changing the position of the exhaust connectionWindow connection Wall connection with rigid pipeChimney connection Direct wall connection Dryer top viewCollective exhaust duct Technical Data Caring for the environment Disposal of the packing materialsDisposal of an appliance Menu Settings To adjust standard settings Settings Opening the menu SettingsSelecting Settings Leaving the Settings menuLanguage Anti-crease Time of dayOff NormalNot during current program default setting Delivery status 0 minutes normal cooling down phaseContrast/Brightness StandbySettings Supervisor level Entering the codeSort languages Supervisor levelTimer Language entry Drying levelsCleaning the airways Cleaning the lint filters Normal Factory default LightDisplay the residual moisture as a percentage Cool air freePage Page Page All rights reserved Nr 975 240