Miele PT 7136 PLUS installation manual Program guide

Page 16

Program guide

Programs may vary depending on the offerings of your machine.

Cottons

 

 

Load size: 14.3 lbs (6.5 kg)

Extra dry, Normal+, Normal

 

Items

Single and multilayered cotton and linen laundry e.g. terry towels,

 

beach towels, bath robes, T-Shirts, underwear, cottons bed linens,

 

baby clothing, etc.

 

Note

Select "Low temp." for items with the fabric care symbol ￿.

 

Select "Extra dry" for multilayered and thick items.

 

The "Extra dry" program should not be selected for jersey materials.

 

 

Items may shrink.

 

Hand iron ￿, Hand iron ￿￿, Machine iron

 

Items

Cotton or linen fabrics to be left damp for easier ironing.

 

e.g. table cloths, bed linen, starched laundry, etc.

Note

Select "Low temp." for items with the fabric care symbol ￿.

 

Roll up items until they are ironed to keep them moist.

Minimum iron

Load size: 7.7 lbs (3.5 kg)

Normal+, Normal, Hand iron ￿

 

Items

Permanent Press items of cotton, mixed fabrics or synthetics.

 

e.g. sweaters, dresses, pants, table cloths, etc.

Note

Select "Low temp." for items with the fabric care symbol ￿.

 

Select "Hand iron ￿" for crease-free drying and reduce the load size

 

 

to (3.3 lbs) 1.5 kg.

 

 

Items will be dried wrinkle free, depending on fabric and load.

The load size is the dry laundry weight.

16

Image 16
Contents Operating and Installation manual Vented Dryer PT 7136 Plus Contents Contents Important Safety Instructions Important Safety Instructions Save These Instructions Guide to the dryer Control panelDisplay function Main menuJog shuttle Program selection possibilityMenu Program selection SettingsBasic menu of a drying program Before using for the first time Welcome screenLanguage Set the time of dayFabric care labels UseDrying tips Sort the laundry Load the laundrySelect Low temp. and/or Timer Select a programInsert coins if operated by coin mechanism Starting a programCleaning and care hints At the end of a programRemaining time Before the end of a programCanceling a program Coin mechanismAdding/removing laundry during a drying program Continue dryingProgram guide Woollen handcare SmoothingCool air Warm airJeans Normal, Hand ironShirts ProofingTimer Select the submenu TimerStarting the timer function Canceling the timerSelecting/Changing a Favorite FavoritesBasic menu Program Warm air, Cool air Drying level programsOther programs Saving a Favorite Low tempAssigning a direct select button Cleaning and Care Cleaning the lint filterRemoving the lint filter Disassembling the lint filterClean the lint filters dry Clean the lint filters wetCleaning the exterior and the control panel Inserting the lint filterCheck and fault messages in the display Frequently asked questionsWhat if Possible cause Solution Program What if Possible cause Solution At the end of aAppears Other faults What if Possible fault Solution What if there is Condensed waterDrum? Items madeWhat if Possible cause Solution Program cannot Start indicatorBe started, Display remainsChanging the light bulb After sales service Optional accessoriesInstallation Instructions Important Safety Instructions Save These Instructions Installation Front viewSide view Rear view Top view Washer/ Dryer Stack Installation on a cement base Coin mechanism Transporting the dryer to the installation site InstallationLevel the dryer Electrical connection Installation of exhaust venting General notesHow to calculate the effective duct length Tips about the ductwork Additional duct lengths 4 rigid pipe only Length Determining the position of the exhaust connection Changing the position of the exhaust connectionWindow connection Wall connection with rigid pipeChimney connection Direct wall connection Dryer top viewCollective exhaust duct Technical Data Disposal of the packing materials Caring for the environmentDisposal of an appliance Menu Settings To adjust standard settings Settings Opening the menu SettingsSelecting Settings Leaving the Settings menuLanguage Anti-crease Time of dayOff NormalNot during current program default setting Delivery status 0 minutes normal cooling down phaseContrast/Brightness StandbySettings Supervisor level Entering the codeSort languages Supervisor levelTimer Language entry Drying levelsCleaning the airways Cleaning the lint filters Normal Factory default LightDisplay the residual moisture as a percentage Cool air freePage Page Page All rights reserved Nr 975 240